Chrysler 2007 Aspen User Manual

TABLE OF CONTENTSSECTION PAGE1INTRODUCTION...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE..

▫ General Information ...22▫ Programming Additional Transmitters ...23▫ Battery Replacement ...24䡵 Remote Start

If you would like to connect or disconnect the Blue-tooth™ connection between a UConnect™ paired cellularphone and the UConnect™ system, then follow t

Delete UConnect™ Paired Cellular Phones•Press the ’Phone’ button to begin.•After the ⬙Ready⬙ prompt and the following beep, say⬙Setup Phone Pairing.⬙•

Voice Recognition (VR)•Always wait for the beep before speaking.•Speak normally, without pausing, just as you wouldspeak to a person sitting approxima

•Even though international dialing for most numbercombinations is supported, some shortcut dialingnumber combinations may not be supported.Far End Aud

104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1053

106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice CommandsPrimary Alternate(s)zeroonetwothreefourfivesixseveneightninestar (*)plus (+)pound (#)add locationallcallcancelconfirmation promptscontin

mobilemutemute offnew entrynopagerpair a phonephone pairing pairingphonebook phone bookpreviousrecord againredialreturn to main menu return or main me

WARNING!Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seat couldcause you to lose control. The seat belt might

▫ Driver And Right Front Passenger SupplementalRestraint System (SRS)—Airbags ...51▫ Event Data Recorder (EDR) ...60▫ Child Restra

WARNING!Do not ride with the seatback reclined so that theshoulder belt is no longer resting against your chest.In a collision you could slide under t

To lower the head restraint, depress the release buttonlocated at the base of the head restraint and push downon the head restraint.8 - Way Driver’s P

4 - Way Passenger’s Power Seat — If EquippedThe front passenger’s power seat switches are located onthe right side of the passenger seat lower side tr

With the ignition switch in the RUN position, depressingthe heated seat switch rocker to its momentary high orlow position provides power to the heate

off. Both of the indicators on identifies High heat level.The lower indicator on only, identifies Low heat level.NOTE: The high heat setting will oper

Second Row Bucket Seats — Fold and TumbleSecond row bucket seats have seatback recliners on bothseating positions. Raising the lever allows the seatba

4. Pull up on the release handle and lift to tumble theseat fully forward. If the seat contacts the rear of the frontseat, move the front seat forward

WARNING!In a collision, you or others in your vehicle could beinjured if seats are not properly latched to their floorattachments. Always be sure the

Second row leather seats have seatback recliners at the40% seating positions. Raising the lever allows the seat-back to be reclined an additional 11 d

To Tumble the 40% seat, fully raise the lever on the sideof the seat to release the floor latches and tumble the seat.WARNING!Do not drive the vehicle

A WORD ABOUT YOUR KEYSThe dealer that sold you your new vehicle has the keycode numbers for your vehicle locks. These numbers canbe used to order dupl

NOTE: The seatback must be fully folded into the downposition to allow the lever to be raised enough to releasethe floor latches.To Fold and Tumble th

Seat Cushion Pockets Seat Cushion Movement Up And ForwardUNDERSTANDING THE FEATURES OF YOUR VEHICLE 1213

CAUTION!When loading cargo into the rear of you vehicle withthe 3rd row seat folded flat, be careful not to damagethe material on the head restraints.

Third Row 60/40 Folding — If EquippedThird Row SeatThird Row Seat 40% Seatback FoldUNDERSTANDING THE FEATURES OF YOUR VEHICLE 1233

Third Row Seat Features Third Row Seat Folded Forward124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

DRIVER MEMORY SYSTEM — IF EQUIPPEDOnce programmed, the memory buttons 1 and 2 on thedriver’s door panel can be used to recall the driver’s seatpositio

Setting Memory Positions and Linking RemoteKeyless Entry Transmitter to MemoryNOTE: Each time the SET (S) button and a numberedbutton (1 or 2) are pre

Memory Position RecallNOTE:•The driver’s seat belt must be unbuckled to recallmemory positions.•The vehicle must be in Park to recall memory posi-tion

3. Within 10 seconds, press and release the UNLOCKbutton on the Remote Keyless Entry transmitter.To disable another transmitter linked to either memor

the seat is positioned rearward enough and no benefitfrom moving the seat any farther rearward.NOTE: The Easy Entry/Easy Exit feature can be en-abled

in the ignition cylinder. If this occurs, rotate the key to theright slightly, then remove the key as described. If amalfunction occurs, the system wi

Then push the safety latch lever to the left. It is locatedbetween the grille and hood opening right of the center.To prevent possible damage, do not

LIGHTSHeadlight Switch LocationHeadlight SwitchUNDERSTANDING THE FEATURES OF YOUR VEHICLE 1313

Interior LightsCourtesy and dome lights are turned on when the frontdoors are opened, when the dimmer control (rotatingwheel on the right side of the

If the ignition is off and any door is left ajar for eightminutes or the dimmer control is rotated upwards for 15minutes, the interior lights will aut

Headlights, Parking Lights, Panel LightsWhen the headlight switch is rotated to the first positionto the right, the parking lights, taillights, side m

Lights-on ReminderIf the headlights, parking lights, or courtesy lights are leftOn, after the ignition is turned Off, a continuous fastchime will soun

of the front and rear turn signal lights. If an indicator failsto light when the lever is moved, it would suggest thatthe switch or indicator lamp is

Passing LightYou can signal another vehicle with your headlights bypartially pulling the multifunction lever toward the steer-ing wheel. This will mom

WINDSHIELD WIPERS AND WASHERSWindshield WipersThe wipers and washers are operated by a switch in themultifunction control lever. Turn the end of the h

NOTE: Avoid using the wiper blades to remove frost orIce from the windshield.NOTE: If the front wiper is operating when the ignitionis turned off, the

inserted or withdrawn only in the LOCK position. Pushin on the key in the ignition lock cylinder to rotate to theLOCK position.WARNING!The key cannot

TILT STEERING COLUMNTo tilt the column, pull rearward on the lever below theturn signal control and move the wheel up or down, asdesired. Push the lev

DRIVER ADJUSTABLE PEDALS — IF EQUIPPEDThe power adjustable accelerator and brake pedals allowthe driver to establish a comfortable position relative t

CAUTION!Do not place any article under the adjustable pedalsor impede its ability to move as it may cause damageto the pedal controls. Pedal travel ma

To ActivateNOTE: Activating any two speed control switch func-tions simultaneously (i.e. SET and CANCEL) will causethe speed control system to shut of

To Resume SpeedTo resume a previously set speed, push and release theRESUME button. Resume can be used at any speed above(refer to the table below for

Functions 4.7L 5.7LEngage Speed 35 mph (56 km/h) 25 mph (40 km/h)Minimun RESUME Speed 30 mph (50 km/h) 20 mph (32 km/h)ACCEL Increase 2 mph (3km/h) 1

WARNING!Speed Control can be dangerous where the systemcan’t maintain a constant speed. Your vehicle couldgo too fast for the conditions, and you coul

The warning display contains two sets of yellow and redLEDs, one set to warn of obstacles behind the left rear ofthe vehicle and the other set to warn

WARNING DISPLAY DISTANCESDISPLAY LED OBSTACLE DISTANCE FROM: LED COLOR AUDIBLE SIGNALREAR CORNERS REAR CENTER1st LED 59 in. (150 cm) Yellow None2nd LE

WARNING!•Drivers must be careful when backing up even whenusing the Rear Park Assist System. Always checkcarefully behind your vehicle, look behind yo

For vehicles equipped with the Electronic Vehicle Infor-mation Center (EVIC), the power window switches,radio, hands–free system (if equipped), and po

NOTE:•Ensure that the rear bumper is free of dirt and debristo keep the system operating properly.•Jackhammers, large trucks, and other vibrations cou

Courtesy/Reading LightsNear the front of the console are two courtesy/readinglights.Both lights illuminate as courtesy lights when a door isopened, wh

NOTE: The dome/reading lights will remain on untilthe switch is pressed a second time, so be sure they havebeen turned off before leaving the vehicle.

Trip FunctionsPressing the STEP button allows you to scroll throughone of the following Trip Function features:•TRIP – Shows the total distance travel

change to a text display of ⬙LOW FUEL.⬙ This displaywill continue until the vehicle runs out of fuel. Addinga significant amount of fuel to the vehicl

•COOLANT LOW•ESP SYSTEM DEACTIVATED•LIFTGATE OPENPersonal Settings (Customer ProgrammableFeatures)Personal Settings allows the driver to set and recal

remote keyless entry unlock button twice to unlock thepassenger’s doors. To make your selection, press andrelease the RESET button until “DRV DR 1st ”

•HEADLAMPS W /WIPERS > YES – When ON isselected, the headlamps will automatically turn onwhen the wiper switch is activated.•EASY EXIT SEAT > YE

change your variance according to your variance onthe variance map. Refer to Compass Variance, in thissection for additional information.•“COMPASS CAL

3. Press the STEP button until “Calibrate Compass YES”is displayed.4. Press and release the RESET button to start the cali-bration. The message “CAL”

If the Vehicle Security Alarm Indicator Light turns onduring normal vehicle operation (vehicle running forlonger than 10 seconds), it indicates that t

1. Turn the ignition switch to the ON/RUN position.2. Press the menu button until Personal Set-tings is displayed.3. Press the STEP button until “Comp

WARNING!A moving garage door can cause injury to people andpets in the path of the door. People or pets could beseriously or fatally injured. Only use

Programming HomeLinkThe Electronic Vehicle Information Center (EVIC) fea-tures a driver–interactive display which includesHomeLink system messages. Th

3. Simultaneously press and hold both the HomeLinkbutton that you want to train and the hand-held trans-mitter button. Do not release the buttons unti

6. Firmly press and release the ⬙learn⬙ or ⬙smart⬙ button.(The name and color of the button may vary by manu-facturer.)NOTE: There are 30 seconds in w

NOTE: If programming a garage door opener or gateoperator, it is advised to unplug the device during the⬙cycling⬙ process to prevent possible overheat

SecurityGarage Door Opener Operation with SecurityAlarm (if equipped)If your vehicle is equipped with the Security Alarmfeature, the operation of the

POWER SUNROOF — IF EQUIPPEDThe power sunroof control is located between the sunvisors on the overhead console.Pressing the ⬙open⬙ end of the rocker sw

WARNING!Never leave children alone in a vehicle. Leavingchildren in a vehicle unattended is dangerous for anumber of reasons. A child or others could

the rear windows open, open the front and rear windowstogether to minimize the buffeting. If the buffeting occurswith the sunroof open, adjust the sun

4. Insert a blank Sentry Key into the ignition switch andturn the ignition switch ON within 60 seconds. After 10seconds a single chime will sound and

115V Inverter Outlet – If EquippedThis vehicle may also be equipped with a 115 Volt (150Watts Maximum) outlet on the rear of the front centerconsole.

Electrical Outlet Use With Engine OFF (BatteryFed Configuration)CAUTION!•Many accessories that can be plugged in draw powerfrom the vehicle’s battery,

Reconfiguring Power OutletsTo reconfigure the outlets, be sure the ignition is OFFbefore removing the fuse. The reconfigurable fuse loca-tion is a spe

•Portable phone storage bin•Portable phone cord routing between lid and base onforward edge•12 Volt reconfigurable power outlet inside storagecompartm

The front storage bin in the center console is equippedwith a removable bin mat. This mat can be removed bypulling on the tab located on the front edg

being stored in the bin. To use, plug in the portable powerrecharge cord and place the cord along the openingunder the forward portion of the storage

FACTORY INSTALLED ROOF LUGGAGE RACKThe load carried on the roof when equipped with aluggage rack must not exceed 68 kg (150 lbs.), and shouldbe unifor

CAUTION!To avoid damage to the roof rack and vehicle, do notexceed the maximum roof rack load capacity. Alwaysdistribute heavy loads as evenly as poss

CARGO MANAGEMENT SYSTEM—IF EQUIPPEDThe cargo management system consists of a removablecargo liner and removable cargo organizer.To open the side cover

To open the Cargo divider, lift up on the cargo dividerhandles, raising the doors to the full open position. Raisethe side panels until they engage in

To Set the Alarm:The alarm will set when you use the power door locks oruse the Keyless Entry transmitter to lock the doors. Afterall the doors are lo

INSTRUMENT PANEL AND CONTROLSCONTENTS䡵 Instruments And Controls ...185䡵 Instrument Cluster ...186䡵 Instrument Cluster

▫ Operating Instructions - Hands Free Phone —If Equipped ...207▫ Operating Instructions - Satellite Radio —If Equipped ...

▫ Selecting a Channel ...228▫ Storing And Selecting Pre-Set Channels ...229▫ Using The PTY (Program Type) Button(If Equipped) ...

▫ Rear Rotary Temperature Control ...245▫ Front Unit To Rear Unit Chart ...246▫ Operating Tips ...246▫ Operating T

INSTRUMENTS AND CONTROLSINSTRUMENT PANEL AND CONTROLS 1854

Instrument Cluster186 INSTRUMENT PANEL AND CONTROLS

INSTRUMENT CLUSTER DESCRIPTION1. Fuel GageThe fuel gauge shows level of fuel in tank whenignition switch is in the ON position.2. Temperature GageThe

left/right turn signal is left on with the engine RPMvehicle speed greater than 15 mph (24 km/h) for morethan one mile.4. Low Fuel Warning LightThis i

CAUTION!Driving with a hot engine cooling system coulddamage your vehicle. If the temperature light is on,safely pull over and stop the vehicle. Idle

ILLUMINATED ENTRYVehicles Equipped With Power Door LocksAll interior lights will illuminate in the vehicle when thedoors are unlocked using the key fo

11. Security LightThis light will flash rapidly for approximately 15 secondswhen the vehicle theft alarm is arming. The light willflash at a slower sp

15. Gear SelectorThe electronic gear selector display is self-containedwithin the instrument cluster. It displays the position ofthe automatic transmi

replacement, be sure to keep a record of the readingbefore and after the service so that the correct mileage canbe determined.18. Electronic Stability

on for 15 seconds as a bulb check. If the light does notcome on during starting, have the system checked by anauthorized dealer.21. BRAKE System Warni

NOTE: • ⬙The ⬙ESP/TCS Indicator Light⬙ and the ⬙ESP/BAS Warning Lamp⬙ come on momentarily each time theignition switch is turned ON. • The ESP Control

24. Tire Pressure Monitoring Telltale LightEach tire, including the spare (if provided),should be checked monthly when cold andinflated to the inflati

CAUTION!The TPMS has been optimized for the originalequipment tires and wheels. TPMS pressures andwarning have been established for the tire sizeequip

29. TOW/HAULThe TOW/HAUL button is located at the end of the gearshift lever. This light will illuminate when the TOW/HAUL button has been selected.30

5. To exit, press any button/knob or wait approximately5 seconds.SETTING THE ANALOG CLOCKTo set the analog clock at the top center of the instrumentpa

Electrical DisturbancesRadio waves may pick up electrical disturbances duringtransmission. They mainly affect the wave amplitude,and thus remain a par

NOTE: Your vehicle’s keyfob may have three, four orfive buttons (shown), depending on the optional featurespurchased with your vehicle.This system all

SALES CODE REF — AM/FM/CD (SINGLE DISC)RADIO WITH OPTIONAL SATELLITE RADIO ANDHANDS FREE PHONE CAPABILITYNOTE: The radio sales code is located on the

Mode Button (Radio Mode)Press the mode button repeatedly to select between theCD player and Satellite Radio (if equipped).SEEK Button (Radio Mode)Pres

Clock Setting Procedure1. Press and hold the time button until the hours blink.2. Adjust the hours by turning the right side Tune/Audio control.3. Aft

Press the rotary TUNE control a fourth time and BAL willdisplay. Turn the TUNE control to the right or left toadjust the sound level from the right or

Operation Instructions - CD ModeNOTE: The ignition switch must be in the ON or ACCposition to operate the radio.Inserting The Compact Disc (Single CD

SCAN Button (CD Mode)Press this button to play the first 10 seconds of each track.To stop the scan function, press the button a second time.EJECT Butt

Operation Instructions - Auxiliary ModeThe auxiliary (AUX) jack is an audio input jack, whichallows the user to plug in a portable device such as anMP

TIME Button (Auxiliary Mode)Press this button to change the display from elapsedplaying time to time of day. The time of day will displayfor 5 seconds

SALES CODE RAQ – AM/FM/CD (6-DISC) RADIOWITH OPTIONAL SATELLITE RADIO, HANDSFREE PHONE, AND VEHICLE ENTERTAINMENTSYSTEMS (VES) CAPABILITIESNOTE: The r

Mode Button (Radio Mode)Press the mode button repeatedly to select between theCD player, Satellite Radio, or Vehicle EntertainmentSystem (VES) (if equ

5. If the desired programming was not achieved or toreactivate this feature, repeat the above steps.To lock the doors and liftgate:Press and release t

Time ButtonPress the time button and the time of day will bedisplayed for 5 seconds.Clock Setting Procedure1. Press and hold the time button until the

Press the rotary TUNE control a third time and TREBLEwill display. Turn the TUNE control to the right or left toincrease or decrease the Treble tones.

Jazz JazzNews NewsNostalgia NostalgiaOldies OldiesPersonality PersonalityPublic PublicRhythm and Blues Rhythm_and_BluesReligious Music Religious_Music

You may add a second station to each push-button byrepeating the above procedure with this exception: Pressthe SET/DIR button twice and SET 2 will sho

CAUTION!This CD player will accept 4 3/4 inch (12 cm) discsonly. The use of other sized discs may damage theCD player mechanism.You may eject a disc w

LOAD/EJECT Button (CD Mode for CD AudioPlay)LOAD/ EJECT - LoadPress the LOAD/ EJECT button and the push-button with the corresponding number wherethe

TIME Button (CD MODE for CD Audio Play)Press this button to change the display from a large CDplaying time display to a small CD playing time display.

Notes On Playing MP3 FilesThe radio can play MP3 files, however, acceptable MP3file recording media and formats are limited. Whenwriting MP3 files, pa

Supported MP3 File FormatsThe radio will recognize only files with the *.mp3 exten-sion as MP3 files. Non-MP3 files named with the *.mp3extension may

Playback of MP3 FilesWhen a medium containing MP3 data is loaded, theradio checks all files on the medium. If the mediumcontains a lot of folders or f

4. Test the flash lamps with LOCK feature while outsideof the vehicle, by pressing the LOCK button on the keyfob with the ignition in the OFF position

LOAD / EJECT - EjectPress the LOAD/ EJECT button and the push-button with the corresponding number wherethe CD was loaded and the disc will unloadand

AM/FM Button (CD Mode for MP3 Play)Switches back to Radio mode.RND/ PTY Button (CD Mode for MP3 Play)Pressing this button plays files randomly.SET/DIR

SALES CODE REC — AM/FM/CD (6–DISC) RADIOWITH NAVIGATION SYSTEMSatellite Navigation Radio with CD Player with MP3Capability (REC) - combines a Global-P

the worldwide standard for time. This makes the sys-tem’s clock very accurate once the appropriate time zoneand daylight savings information is set.1.

User Defined ClockIf you wish to set the clock to a time different than thesystem clock, you can manually adjust the time bychoosing the “User Defined

Audio Clock DisplaySelect this option to change the size of the clock on theaudio screens.1. When you are at an audio screen, quickly press theTIME bu

VIDEO ENTERTAINMENT SYSTEM (SALES CODEXRV) — IF EQUIPPEDThe optional VES™ (Video Entertainment System) con-sists of a DVD player and LCD (liquid cryst

Electronic Serial Number/Sirius IdentificationNumber (ESN/SID)The Electronic Serial Number/Sirius Identification Num-ber is needed to activate your Si

Selecting Satellite Mode in REF, RAQ, and RAKRadiosSelecting Satellite Mode — REF RadioPress the MODE button repeatedly until the word ⬙SAT⬙appears in

Storing and Selecting Pre-Set ChannelsIn addition to the 12 AM and 12 FM pre-set stations, youmay also commit 12 satellite stations to push buttonmemo

NOTE: Changes or modifications not expressly ap-proved by the party responsible for compliance couldvoid the user’s authority to operate the equipment

Reception QualitySatellite reception may be interrupted due to one of thefollowing reasons.•The vehicle is parked in an underground parkingstructure o

The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch willincrease the volume and pressing th

COMPACT DISC MAINTENANCETo keep the compact discs in good condition, take thefollowing precautions:1. Handle the disc by its edge; avoid touching thes

CLIMATE CONTROLSManual ControlThe Air Conditioning and Heating System is designed tomake you comfortable in all types of weather. Thefollowing describ

engine speed or power may be noticed when the com-pressor cycles. This is a normal occurrence since thecompressor will cycle on and off to maintain co

Recirculation Mode (Panel or Bi-Level)Select either the Panel or Bi-Levelmode positions when the outside aircontains smoke, odors, high humidity,or if

DefrostOutside air is primarily directed to the windshieldthrough the defroster outlet located at the base ofthe windshield and side window demist out

Rear Temperature Control — If EquippedRotating this knob left to the“REAR CONTROL” positionallows the passengers in thesecond and third row seats toco

Automatic Temperature Control (ATC) — IfEquippedThe control can be turned on by pressing the POWERknob. When the control is turned on, it will be in t

located in the overhead console to measure the tem-perature of the driver and passengers. Based on thesensor input, the system will automatically ocnt

7. When a single chime is heard release both buttons. Thechime is an indication that you have successfully enteredprogram mode. All fobs that are to b

Manual Control (ATC)You also may choose to customize your comfort byselecting the fan speed and mode manually. Turning thefan speed knob or any mode b

Recirculate ButtonPress this button to recirculate the air inside thevehicle. Outside air is prevented from enteringthe vehicle. Use this mode to temp

Bi-LevelAir flows through the outlets located in the instru-ment panel and those located on the floor.NOTE: There is a difference in temperature betwe

CONTROL IN REARThis allows the passengers in the second row seats tocontrol the blower speed and temperature by means ofthe rear control located in th

Rear Zone Climate Control — If EquippedHeadliner air comes from the outlets in the headliner.Each of these outlets can be individually adjusted todire

Rear Rotary Blower ControlThe second row seat occupants have control of the rearblower speed, only when the front control unit is in the“REAR CONTROL”

Front Unit to Rear Unit ChartIf the Front Control isselectedRear Airflow will comefromPanel HeadlinerBi-Level HeadlinerFloor FloorMix FloorDefrost Flo

Regular cleaning of the inside of the windows with anon-filming cleaning solution (vinegar and water worksvery well) will help prevent contaminates (c

Operating Tips Chart248 INSTRUMENT PANEL AND CONTROLS

REAR WINDOW FEATURESRear Window Wiper/WasherA rotating switch located on the climate controlpanel turns the rear wiper On or Off. Pressing therotating

2. Remove and replace the batteries. Avoid touching thenew batteries with your fingers. Skin oils may causebattery deterioration. If you touch a batte

If the rear wiper is operating when the ignition is turnedoff, the wiper will automatically return to the “Park”position. When the vehicle is restarte

STARTING AND OPERATINGCONTENTS䡵 Starting Procedures ...255▫ Automatic Transmission ...255▫ Normal Starting ...

䡵 Electronic Brake Control System ...279▫ ABS (Anti-Lock Brake System) ...279▫ BAS (Brake Assist System) ...280▫ TCS (Tr

䡵 Snow Tires ...306䡵 Tire Rotation Recommendations ...306䡵 Tire Pressure Monitor System (TPMS) —If Equipped ...

䡵 Vehicle Loading ...321▫ Certification Label ...321▫ Curb Weight ...323▫ Loading ...

STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust bothinside and outside mirrors, and fasten your seat belts.WARNING!Be sure t

’Start’ position until the vehicle starts, but can release thekey (still in the ignition) and the vehicle will continuethrough the start cycle.•Turn t

WARNING!Do not attempt to push or tow your vehicle to get itstarted. Vehicles equipped with an automatic trans-mission cannot be started this way. Unb

The 4.7L engine block heater cord is located at the front ofthe engine compartment near the radiator cap. The 5.7Lengine block heater cord is located

“P” ParkSupplements parking brake by locking the transmission.Engine can be started in this range. Never use Park whilevehicle is in motion. Apply par

To remote start your vehicle, press the REMOTE STARTbutton on the key fob twice within three seconds. Toindicate that the vehicle is about to start, t

WARNING!It is dangerous to shift the selector lever out of “P” or“N” if the engine speed is higher than idle speed. Ifyour foot is not firmly on the b

“1” FirstFor driving up very steep hills and for engine braking atlow speeds 25 mph (40 km/h) or less when going downhill. To prevent excessive engine

The transmission will downshift from Overdrive to Driveif the accelerator pedal is fully depressed at vehiclespeeds above approximately 35 mph (56 km/

light throttle. It engages at higher speeds under heavieracceleration. This may result in a slightly different feelingor response during normal operat

When additional traction is required, the transfer case4WD LOCK position can be used to lock the front andrear driveshafts together and force the fron

shift to take place. Shifting while only the front or rearwheels are spinning can cause damage to the transfercase.Proper operation of four-wheel-driv

Shifting Procedure - NV 144 Transfer Case4WD to 4WD LOCK or 4WD LOCK to 4WDWith the key ON and the engine either OFF or RUN-NING, rotate the transfer

If the key is not ON then the shift will not take place andno position indicator lights will be on or flashing.NV 244 Generation II Transfer Case Oper

NOTE: The transfer case Neutral (N) position is to beused for recreational towing only. See Recreational Tow-ing section for specific procedures on sh

When operating your vehicle in 4WD LOW, the enginespeed is approximately three times that of the 4WD or4WD LOCK positions at a given road speed. Take

The vehicle can be started remotely up to a maximum oftwo times. The vehicle is also allowed a maximum of onefailed start, where the remote start sequ

4WDNormal Four-Wheel-Drive High Range - Employs inter-axle differential. Allows front and rear wheels to rotate atdifferent speeds. All road surfaces.

Shifting Procedure - NV 244 Generation IITransfer CaseNOTE: The 4x4 system will not allow shifts between4WD/ 4WD LOCK if the rear wheels are spinning

3. While still rolling, rotate the transfer case controlswitch to the desired position.4. After the position indicator light has stopped flashing,shif

3. Replace tires when tread wear indicators first becomevisible.4. Keep tires properly inflated.5. Maintain sufficient distance between your vehicle a

NOTE: The instrument cluster brake warning lightindicates only that the parking brake is applied. You mustbe sure the parking brake is fully applied b

BRAKE SYSTEMIn the event power assist is lost for any reason, (forexample, repeated brake applications with the engineoff), the brakes will still func

At the instant one of the wheels is about to lock up, aslight pulsation can be felt in the brake pedal, indicatingthat the ABS is in the regulating mo

WARNING!•Anti-lock system (ABS) cannot prevent the natu-ral laws of physics from acting on the vehicle, norcan it increase braking or steering efficie

If for some reason, the power assist is interrupted, it willstill be possible to steer your vehicle. Under these condi-tions you will observe a substa

ELECTRONIC BRAKE CONTROL SYSTEMYour vehicle is equipped with an advanced electronicbrake control system that includes ABS (Anti-Lock BrakeSystem), BAS

Power Door LocksA power door lock switch is on each front door trimpanel. Use this switch to lock or unlock the doors.If you press the power door lock

BAS (Brake Assist System)The BAS is designed to optimize the vehicle’s brakingcapability during emergency braking maneuvers. Thesystem detects an emer

WARNING!•BAS cannot prevent the natural laws of physicsfrom acting on the vehicle, nor can it increasebraking efficiency beyond that afforded by theco

ERM (Electronic Roll Mitigation)This system anticipates the potential for wheel lift bymonitoring the driver’s steering wheel input and thespeed of th

ESP (Electronic Stability Program)This system enhances directional control and stability ofthe vehicle under various driving conditions. ESP cor-rects

WARNING!•ESP (Electronic Stability Program) cannot preventthe natural laws of physics from acting on thevehicle, nor can it increase the traction affo

conditions and more wheel spin than ESP would nor-mally allow is required to gain traction. TSC (TrailerSway Control) is not available when the system

with off road driving but ESP function returns to providethe stability feature at speeds above 30 mph (48 km/h).The ABS is in a special Off-Road mode

several miles at speeds greater than 30 mph (48 km/h),see your authorized dealer as soon as possible to have theproblem diagnosed and corrected.NOTE:•

ROCKING THE VEHICLEIf vehicle becomes stuck in snow, sand, or mud, it canoften be moved by a rocking motion. Move the gearselector rhythmically betwee

•European Metric tire sizing is based on Europeandesign standards. Tires designed to this standard havethe tire size molded into the sidewall beginnin

3. Place the key into the ignition.4. Within 10 seconds, cycle the key from the OFF positionto the ON position a minimum of four times; ending inthe O

Tire Sizing ChartEXAMPLE:Size Designation:P = Passenger car tire size based on U.S. design standardsⴖ...blank...ⴖ = Passenger car tire based on Euro

EXAMPLE:Service Description:95 = Load Index—A numerical code associated with the maximum load a tire can carry.H = Speed Symbol—A symbol indicating th

Tire Identification Number (TIN)The TIN may be found on one or both sides of the tire;however, the date code may only be on one side. Tireswith white

Tire Loading and Tire PressureTire Placard LocationNOTE: The proper cold tire inflation pressure is listedon either the face of the driver’s door or t

LoadingThe vehicle maximum load on the tire must not exceedthe load carrying capacity of the tire on your vehicle. Youwill not exceed the tire’s load

5. Determine the combined weight of luggage and cargobeing loaded on the vehicle. That weight may not safelyexceed the available cargo and luggage loa

296 STARTING AND OPERATING

WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti

2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce tread

CAUTION!After inspecting or adjusting the tire pressure, al-ways reinstall the valve stem cap (if equipped). Thiswill prevent moisture and dirt from e

INTRODUCTIONCONTENTS䡵 Introduction ... 4▫ Roll Over Warning ... 4䡵 How To Use This Manual ...

5. Within 30 seconds, press the driver’s door lock switchin the UNLOCK direction.6. A single chime will sound to indicate the feature hasbeen changed.

loading may be required for high-speed vehicle opera-tion. Refer to original equipment or an authorized tiredealer for recommended safe operating spee

Compact Spare Tire — If EquippedThe compact spare is for temporary emergency use withradial tires. It is engineered to be used on your stylevehicle on

Limited Use Spare — If EquippedThe limited use spare tire is for temporary emergency useon your vehicle. This tire is identified by a limited usespare

WARNING!Fast spinning tires can be dangerous. Forces gener-ated by excessive wheel speeds may cause tire dam-age or failure. A tire could explode and

Life of TireThe service life of a tire is dependent upon varyingfactors including but not limited to:•Driving style•Tire pressure•Distance drivenWARNI

WARNING!•Do not use a tire, wheel size or rating other than thatspecified for your vehicle. Some combinations of un-approved tires and wheels may chan

Improper alignment will not cause vehicle vibration.Vibration may be a result of tire and wheel out-of-balance. Proper balancing will reduce vibration

Follow the recommended tire rotation frequency for yourtype of driving found in the “Maintenance Schedules”Section of this manual. More frequent rotat

The TPM System will warn the driver of a low tirepressure if the tire pressure falls below the low pressurewarning threshold for any reason, including

The Tire Pressure Monitoring Telltale Lamp willilluminate in the instrument cluster, and an au-dible chime will be activated when one or more ofthe fo

WARNING!Avoid trapping anyone in a vehicle in a collision.Remember that the rear doors can only be openedfrom the outside when the child protection lo

CAUTION!The TPMS has been optimized for the originalequipment tires and wheels. TPMS pressures havebeen established for the tire size equipped on your

•The TPMS is not a substitute for proper tire mainte-nance, and it is the driver’s responsibility to maintaincorrect tire pressure, even if under-infl

gasoline will provide no benefit over high quality regularand mid-grade gasolines, and in some circumstancesmay result in poorer performance.Light spa

CAUTION!DO NOT use gasoline containing Methanol or E85Ethanol. Use of these blends may result in startingand driveability problems and may damage crit

Materials Added To FuelAll gasolines sold in the United States are required tocontain effective detergent additives. Use of additionaldetergents or ot

NOTE: Intentional tampering with emissions controlsystems can result in civil penalties being assessedagainst you.Carbon Monoxide WarningsWARNING!Carb

ADDING FUELFuel Filler Cap (Gas Cap)The gas cap is behind the fuel filler door. If the gas cap islost or damaged, be sure the replacement cap is for u

WARNING!•Never have any smoking materials lit in or nearthe vehicle when the gas cap is removed or thetank filled.•Never add fuel when the engine is r

the problem is detected twice in a row, the system willturn on the Malfunction Indicator Light (MIL). Resolvingthe problem will turn the MIL light off

CAUTION!Only vehicles with the E-85 fuel filler door label canoperate on E-85.ETHANOL FUEL (E-85)E-85 is a mixture of approximately 85% fuel ethanol a

windows will operate only when the ignition switch isturned to the ON position and for ten minutes after theignition is turned OFF or the driver’s doo

NOTE: When the ambient temperature is above 90°F,you may experience hard starting and rough idle follow-ing start up even if the above recommendations

MaintenanceIf you operate the vehicle using E-85 fuel, follow Sched-ule B in the maintenance schedule section of this manual.CAUTION!Do not use ethano

Hour of manufacture. The bar code that appears on thebottom of the label is your Vehicle Identification Number(VIN).Gross Vehicle Weight Rating (GVWR)

Curb WeightThe curb weight of a vehicle is defined as the total weightof the vehicle with all fluids, including vehicle fuel, at fullcapacity conditio

WARNING!Do not load your vehicle any heavier than theGVWR or the maximum front and rear GAWR. Ifyou do, parts on your vehicle can break, or it canchan

TRAILER TOWINGIn this section you will find safety tips and informationon limits to the type of towing you can reasonably dowith your vehicle. Before

Gross Axle Weight Rating (GAWR)The GAWR is the maximum capacity of the front and rearaxles. Distribute the load over the front and rear axlesevenly. M

•Trailer Sway Control – MechanicalThe trailer sway control is a telescoping link that can beinstalled between the hitch receiver and the trailer tongu

WARNING!An improperly adjusted Weight Distributing Hitchsystem may reduce handling, stability, braking per-formance, and could result in an accident.W

Fifth-Wheel HitchA special high platform with a coupling that mounts overthe rear axle of the tow vehicle in the truck bed. Connectsa vehicle and fift

NOTE:If the window runs into any obstacle during theauto-closure it will reverse direction and then stop. Re-move the obstacle and use the window swit

Weight Ratings)” for the website address that containsthe necessary information for your specific drivetrain.Trailer Hitch ClassificationClass Max. GT

Never exceed the maximum tongue weight stamped onyour bumper or trailer hitch.Consider the following items when computing theweight on the rear axle o

CAUTION!•Avoid towing a trailer for the first 500 miles (805km) of vehicle operation. Doing so may damageyour vehicle.•During the first 500 miles (805

•Safety chains must always be used between yourvehicle and trailer. Always connect the chains to theframe or hook retainers of the vehicle hitch. Cros

−Check for signs of tire wear or visible tire damagebefore towing a trailer. Refer to the Tires–GeneralInformation section of this manual on Tread Wea

WARNING!Do not connect trailer brakes to your vehicle’s hy-draulic brake lines. It can overload your brake sys-tem and cause it to fail. You might not

Towing TipsBefore setting out on a trip, practice turning, stoppingand backing the trailer in an area away from heavytraffic.If using a manual transmi

NOTE: Check the automatic transmission fluid levelbefore towing.Towing Tips — Tow/Haul (If Equipped)To reduce potential for automatic transmission ove

SNOWPLOWDodge Durango or Chrysler Aspen ModelsNOTE: Do not use Dodge Durango or Chrysler AspenModels for snowplow applications.WARNING!Snowplows, winc

RECREATIONAL TOWING (BEHINDMOTORHOME, ETC.)Recreational Towing 2WD ModelsRecreational towing of 2WD models is not allowable.Towing the vehicle with th

LIFTGATEThe liftgate can be unlocked using the remote keylessentry transmitter or by activating the power door lockswitches located on the front doors

NOTE: The NV 244 Generation II transfer case must beshifted into Neutral (N) for recreational towing. TheNeutral (N) selection button is located on th

11. Repeat steps 9 and 10 with the transmission in Drive(D).12. Turn ignition key to the unlocked OFF position.13. Shift automatic transmission into P

3. Turn the ignition key to the ON position withoutstarting the engine.4. Depress brake pedal.5. Shift automatic transmission to Neutral (N).6. Using

CAUTION!•Do not use a bumper mounted clamp-on tow baron your vehicle. The bumper face bar will bedamaged.•Do not disconnect the rear driveshaft becaus

WHAT TO DO IN EMERGENCIESCONTENTS䡵 Hazard Warning Flasher ...346䡵 Jacking And Tire Changing ...347▫ Jack Location ...

HAZARD WARNING FLASHERThe flasher switch is on the top of the steering column,just behind the steering wheel. Press the flasher switchand all front an

JACKING AND TIRE CHANGINGWARNING!•Being under a jacked-up vehicle is dangerous.The vehicle could slip off the jack and fall on you.You could be crushe

JACKING INSTRUCTIONSRemoving The Spare TireThe spare tire on your vehicle is located underneath thevehicle in the rear.Remove the spare tire before at

It is recommended that you stow the flat or spare toavoid tangling the loose cable.CAUTION!The winch mechanism is designed for use with thejack extens

The liftgate will not manually open if the vehicle is ingear or the vehicle speed is above 0 mph (0 km/h).NOTE:•If the liftgate is locked and is not e

PreparationsPark the vehicle on a firm level surface, avoiding ice orslippery areas. Set the parking brake and place the gearselector in PARK (automat

3. When changing a front wheel, place the jack under theframe rail behind the wheel. Locate the jack as farforward as possible on the straight part of

Before raising the wheel off the ground, make sure thatthe jack will not damage surrounding truck parts andadjust the jack position as required.4. By

WARNING!A loose tire or jack thrown forward in a collision orhard stop could injure someone in the vehicle.Always stow the jack, tools and the extra t

To Stow The Flat Or SpareTurn the wheel so that the valve stem is down. Slide thewheel retainer through the center of the wheel andposition it properl

Check the Battery Test Indicator (if equipped). If a light orbright colored dot is visible in the indicator (if equipped),DO NOT jump-start the batter

WARNING!Do not connect the cable to the negative post of thedischarge battery. The resulting electrical sparkcould cause the battery to explode.During

WARNING!Chains are not recommended for freeing a stuckvehicle. Chains may break, causing serious injury ordeath.WARNING!Stand clear of vehicles when p

Four-Wheel Drive VehiclesThe manufacturer recommends towing with all wheelsOFF the ground. Acceptable methods are to tow thevehicle on a flatbed or wi

MAINTAINING YOUR VEHICLECONTENTS䡵 Engine Compartment 4.7L V-8 ...362䡵 Engine Compartment 5.7L HEMI V-8 ...363䡵 Onboard Diagnostic Sys

NOTE:•In the event of a power malfunction to the liftgate, anemergency liftgate latch release can be used to openthe liftgate. The emergency liftgate

▫ Power Steering — Fluid Check ...377▫ Front Suspension Ball Joints ...377▫ Drive Shaft Constant Velocity Joints ...378▫ Body

▫ Center High-Mounted Stoplight ...412▫ Fog Lights ...413䡵 Fluids And Capacities ...414䡵 Fluids, Lubric

ENGINE COMPARTMENT 4.7L V-8362 MAINTAINING YOUR VEHICLE

ENGINE COMPARTMENT 5.7L HEMI V-8MAINTAINING YOUR VEHICLE 3637

ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor

cap until a ⬙clicking⬙ sound is heard. This is an indicationthat the gas cap is properly tightened. Press the odometerreset button to turn the message

3. As soon as you turn your key to the ON position, youwill see your MIL symbol come on as part of a normalbulb check.4. Approximately 15 seconds late

DEALER SERVICEYour dealer has the qualified service personnel, specialtools and equipment to perform all service operations inan expert manner. Servic

could adversely affect the engine or vehicle performance.These items should be inspected if a malfunction isobserved or suspected.Engine OilChecking O

Change Engine OilRoad conditions and your style of driving affect theinterval at which your oil should be changed. Check thefollowing to determine if

•The power liftgate must be in the full open position forany of the buttons to operate. If the liftgate is not fullyopen, press the remote keyless ent

Dusty ConditionsDriving through dust-laden air increases the problems ofkeeping abrasive materials out of the engine. Under theseconditions, special a

Lubricants which do not have both, the engine oil certi-fication mark and the correct SAE viscosity grade num-ber should not be used.Synthetic Engine

Drive Belts — Check Condition and TensionBelt tension is controlled by means of an automatictensioner. No belt tension adjustments are required.Howeve

Engine Air Cleaner FilterUnder normal driving conditions, replace the air filter atthe intervals shown on Schedule “A”. If, however, youdrive the vehi

CAUTION!Damage to the catalytic converter can result if yourvehicle is not kept in proper operating condition. Inthe event of engine malfunction, part

To minimize the possibility of catalyst damage:•Do not shut off the engine or interrupt the ignitionwhen the transmission is in gear and the vehicle i

CAUTION!•It is essential when replacing the cables on thebattery that the positive cable is attached to thepositive post and the negative cable is att

Refrigerant Recovery and RecyclingR-134a Air Conditioning Refrigerant is a hydrofluorocar-bon (HFC) that is endorsed by the Environmental Pro-tection

Drive Shaft Constant Velocity JointsAll four wheel drive models are equipped with fourconstant velocity joints. Periodic lubrication of thesejoints is

Avoid using the wiper blades to remove frost or ice fromthe windshield. Keep the blade rubber out of contact withpetroleum products such as engine oil

WARNING!•Driving with the liftgate open can allow poison-ous exhaust gases into your vehicle. You and yourpassengers could be injured by these fumes.

Exhaust SystemThe best protection against carbon monoxide entry intothe vehicle body is a properly maintained engine exhaustsystem.Whenever a change i

Cooling SystemWARNING!You or others can be badly burned by hot coolant orsteam from your radiator. If you see or hear steamcoming from under the hood,

Cooling System — Drain, Flush and RefillAt the intervals shown on the Maintenance Schedules,the system should be drained, flushed and refilled.If the

Adding CoolantYour vehicle has been built with an improved enginecoolant that allows extended maintenance intervals. Thiscoolant can be used up to 5 Y

WARNING!•The warning words “DO NOT OPEN HOT” onthe cooling system pressure cap are a safety pre-caution. Never add coolant when the engine isoverheate

When additional coolant is needed to maintain theproper level, it should be added to the coolant bottle. Donot overfill.Points To RememberNOTE: When t

•Do not change the thermostat for summer or winteroperation. If replacement is ever necessary, installONLY the correct type thermostat. Other designs

Positive Crankcase Ventilation (PCV) ValveProper operation of the crankcase ventilation systemrequires that the PCV valve be free of sticking or plug-

WARNING!Use of brake fluid that may have a lower initialboiling point, or is unidentified, as to specificationsmay result in sudden brake failure duri

WARNING!Worn brake hoses can burst and cause brake failure.You could have an accident. If you see any sign ofcracking, scuffing, or worn spots, have t

WARNING!In a collision, you and your passengers can suffermuch greater injuries if you are not properly buck-led up. You can strike the interior of yo

a minimum of two (2) minutes for the oil to fully draininto the transmission before rechecking the fluid level.NOTE: If it is necessary to check the t

CAUTION!Using a transmission fluid other than the manufac-turers recommended fluid may cause deteriorationin transmission shift quality and/or torque

AxlesRefer to Fluids, Lubricants and Genuine Parts for correctfluid type.The manufacturer does not recommend regularly sched-uled oil changes for axle

be used for chassis lubrication. Use only those greasesthat have the NLGI symbol on the container along withthe proper quality level for your applicat

•Use Mopar威 auto polish to remove road film andstains and to polish your vehicle. Take care never toscratch the paint.•Avoid using abrasive compounds

•Use Mopar威 touch up paint on scratches as soon aspossible. Your dealer has touch up paint to match thecolor of your vehicle.Wheel and Wheel Trim Care

Mopar威 Total Clean is specifically recommended forleather upholstery.Your leather upholstery can be best preserved by regularcleaning with a damp soft

Glass SurfacesAll glass surfaces should be cleaned on a regular basiswith any commercial household-type glass cleaner.Never use an abrasive type clean

FUSE BLOCKCAUTION!When replacing a blown fuse, it is important to useonly a fuse having the correct amperage rating. Theuse of a fuse with a rating ot

Cavity Mini Fuse/Color DescriptionF1 15 Amp BlueInstrument ClusterBattery FeedF 2 10 Amp Red SpareF3 10 Amp RedIgnition Run/Start forNext Generation C

INTRODUCTIONThis manual has been prepared with the assistance ofservice and engineering specialists to acquaint you withthe operation and maintenance

WARNING!It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, peopleriding in these areas are more likely

F8 10 Amp RedIgnition Run/Start forCluster/TransferCase/Seat Sw. BacklightingF9 10 Amp RedSatellite Digital AudioReceiver (SDAR)/Digital Video Disc(DV

Fuses (Power Distribution Center)Your vehicle is equipped with an electrical power distri-bution center located in the left side of the enginecompartm

CavityCartridgeFuse /RelayMini Fuse Description7 40 AmpGreenBlower Motor RelayFeed8 40 AmpGreenJB Feed Acc Delay9 Spare10 30 AmpPinkASD11 40 AmpGreenP

CavityCartridgeFuse /RelayMini Fuse Description23 20 AmpYellowTrailer Tow24 15 AmpBlueA/C Clutch25 15 AmpBlueStop Lamp Switch26 Spare27 20 AmpYellowRu

Fuses (Integrated Power Module)An integrated Power Module is located in the left side ofthe engine compartment. This center contains cartridgefuses, m

CavityCartridgeFuse /RelayMini Fuse Description10 10 AmpRedRt Park Lamps11 Relay Radiator Fan Hi Rly12 20 AmpYellowFront Control Module(FCM) Batt #413

CavityCartridgeFuse /RelayMini Fuse Description27 30 AmpGreenIgnition Off Draw(IOD) #128 30 AmpGreenIgnition Off Draw(IOD) #229 Spare30 SpareVEHICLE S

REPLACEMENT LIGHT BULBSLIGHT BULBS — Interior Bulb No.Dome Light ... WL212–2Liftgate Lamp ... 567Overhead

2. Remove one nut that attaches the headlight to theinner fender panel. Access to the nut is possible byopening the fender panel access door which is

Tail Lights, Turn Signals And Backup Lights —Replacement1. Remove the two push-pins from the tail light housing.2. Rotate the light to the outboard si

Lap/Shoulder Belt Operating Instructions1. Enter the vehicle and close the door. Sit back andadjust the seat.2. The seat belt latch plate is above the

3. Unlock and remove electrical connector. 4. Twist bulb sockets counterclockwise to remove fromhousing.5. Remove the bulbs from the bulb sockets by p

License Lights1. Push tab towards the lamp and remove lamp assem-bly.2. Rotate the socket 1/4 turn counterclockwise.3. Pull bulb from socket.MAINTAINI

Center High-Mounted Stoplight1. Remove two screws securing stoplight housing assem-bly to the liftgate.2. Turn socket 1/4 counterclockwise and free fr

Fog LightsTo replace the left foglamp bulb:1. Remove the three wheel liner screws2. Remove the remove the far left air dam screw at thebottom of the f

FLUIDS AND CAPACITIESU.S. MetricFuel4.7L, 87 Octane 27 Gal. 102L5.7L, 89 Octane 27 Gal 102LEngine Oil (with filter)4.7L, SAE 5W-20, API Certified 6 Qt

FLUIDS, LUBRICANTS AND GENUINE PARTSEngineComponent Fluids, Lubricants and Genuine PartsEngine Coolant Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile F

ChassisComponent Fluids, Lubricants and Genuine Parts.Automatic Transmission Mopar威 ATF+4, Automatic Transmission Fluid.Transfer Case Mopar威 ATF+4, Au

MAINTENANCE SCHEDULESCONTENTS䡵 Emission Control System Maintenance ...418䡵 Maintenance Schedules ...418▫ Schedule “B” ...

EMISSION CONTROL SYSTEM MAINTENANCEThe “Scheduled” maintenance services, listed in boldtype on the following pages must be done at the times ormileage

•Off-road or desert operation.•If equipped for and operating with E-85 (ethanol)fuel.NOTE: If ANY of these apply to you then change yourengine oil eve

WARNING!•A belt buckled into the wrong buckle will not protectyou properly. The lap portion could ride too high on yourbody, possibly causing internal

At Each Stop for Fuel•Check the engine oil level about 5 minutes after a fullywarmed engine is shut off. Checking the oil level whilethe vehicle is on

Schedule “B”Follow schedule “B” if you usually operate your vehicleunder one or more of the following conditions.•Day or night temperatures are below

Miles 3,000 6,000 9,000 12,000 15,000(Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000)Change engine oil and engine oil filter, or at 3months wh

Miles 18,000 21,000 24,000 27,000 30,000(Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000)Change engine oil and engine oil filter, or at 3month

Miles 33,000 36,000 39, 000 42,000 45,000(Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000)Change engine oil and engine oil filter, or at 3mont

Miles 48,000 51,000 54,000 57,000 60,000(Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000)Change engine oil and engine oil filter, or at 3 mon

Miles 63,000 66,000 69,000 72,000 75,000(Kilometers) (105 000) (110 000) (115 000) (120 000) (125 000)Change engine oil and engine oil filter, or at 3

Miles 78,000 81,000 84,000 87,000 90,000(Kilometers ) (130 000) (135 000) (140 000) (145 000) (150 000)Change engine oil and engine oil filter, or at

Miles 93,000 96,000 99,000 102,000(Kilometers) (155 000) (160 000) (165 000) (170 000)Change engine oil and engine oil filter, or at 3 monthswhichever

Miles 105,000 108,000 111,000 114,000 117,000 120,000(Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000)Change engine oil and eng

WARNING!• A lap belt worn too high can increase the risk ofinternal injury in a collision. The belt forces won’tbe at the strong hip and pelvic bones,

Miles 105,000 108,000 111,000 114,000 117,000 120,000(Kilometers) (175 000) (180 000) (185 000) (190 000) (195 000) (200 000)Drain and refill automati

Miles 123,000 126,000 129,000 132,000 135,000 138,000(Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) (230 000)Change engine oil and eng

Miles 141,000 144,000 147,000 150,000(Kilometers) (235 000) (240 000) (245 000) (250 000)Change engine oil and engine oil filter at interval shownor 3

Miles 141,000 144,000 147,000 150,000(Kilometers) (235 000) (240 000) (245 000) (250 000)Drain and refill automatic transmission fluid and changemain

Schedule “A”Miles 6,000 12,000 18,000 24,000 30,000(Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000)[Months] [6] [12] [18] [24] [30]Change eng

Miles 36,000 42,000 48,000 54,000 60,000 66,000(Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) (110 000)[Months] [36] [42] [48] [54] [60] [

Miles 72,000 78,000 84,000 90,000 96,000(Kilometers) (120 000) (130 000) (140 000) (150 000) (160 000)[Months] [72] [78] [84] [90] [96]Change engine o

Miles 102,000 108,000 114,000 120,000(Kilometers) (170000) (180 000) (190 000) (200 000)[Months] [102] [108] [114] [120]Change engine oil and engine o

Miles 126,000 132,000 138,000 144,000 150,000(Kilometers) (210 000) (220 000) (230 000) (240 000) (250 000)[Months] [126] [132] [138] [144] [150]Chang

Inspection and service should also be performed anytimea malfunction is observed or suspected. Retain all re-ceipts.** This Maintenance is recommended

Adjustable Upper Shoulder Belt AnchorageIn the front and second row outboard seats, the shoulderbelt can be adjusted upward or downward to helppositio

IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 Suggestions For Obtaining Service For YourVehicle ...442▫ Prepare For The Appointm

SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you’re having warranty work done, be sure to have theright papers with

technicians, special tools, and the latest information toassure your vehicle is fixed correctly and in a timelymanner.This is why you should always ta

Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY)To assist customers who have hearing difficulties, themanufacturer has installed specia

WARRANTY INFORMATION (U.S. Vehicles Only)See the Warranty Information Booklet for the terms andprovisions of DaimlerChrysler’s warranties applicable t

PUBLICATION ORDER FORMSTo order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Mas-tercard, American Ex

Call Toll Free at:•1–800–890–4038 (U.S.)•1–800–387–1143 (Canada)OrVisit us on the World Wide Web at:•www.techauthority.daimlerchrysler.com•www.daimler

INDEX10

WARNING!A 20% seatback that is not fully latched in theupright position will not protect you properly.Second Row Center Seat BeltThe center seating po

ABS (Anti-Lock Brake System) ...190,275Adding Fuel ... 316Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 373Ai

Axle Lubrication (Axle Fluid) ...392Ball Joints ... 377Battery ... 362,363,375Charging ..

Carbon Monoxide Warning ... 72,161,315Cargo Management System ...178Cargo Organizer ...178Cargo Organizer .

Pressure Cap ... 383Radiator Cap ... 383Selection of Coolant (Antifreeze) ...382,414,415Temperature Gau

Emergency, In Case ofFreeing Vehicle When Stuck ... 288Jacking ... 349Tow Hooks ... 356To

FlashersHazard Warning ...346Turn Signal ...135,187,409Flat Tire Stowage ... 348,354Flexible F

Fuses ...172,398,401,404Garage Door Opener (HomeLink威) ...160Gas Cap (Fuel Filler Cap) ... 316,317,364Gas Gauge

HitchesTrailer Towing ...329HomeLink威 (Garage Door Opener) Transmitter . . . 160Hood Release ...129Hoses .

Lane Change and Turn Signals ...135,187,409Lap/Shoulder Belts ... 39,45LATCH (Lower Anchors and Tether for CHildren) . 65Life

Loading Vehicle ...321Tires ...293Locks ...27Automatic Door ...

Rear 60/40 Seat Third Row Center Three PointBelt — If EquippedThe center three point seat belt for the third row rear seatmay be disconnected to allow

Mopar Parts ...366,445Multi-Displacement Engine System ...287Multi-Function Control Lever ...135Navigation R

Pets ...71Pets, Transporting ... 71Phone, Cellular ... 83Phone, Hands-Free

Rear Wiper/Washer ... 249Rearview Mirrors ...79Reclining Front Seats ... 109Recorder, Event

Extender ... 50Front Seat ...39Pretensioners ...48Reminder ...

Speedometer ... 189Starting ...255Automatic Transmission ... 255Emergency (Jump Star

Changing ...348Compact Spare ...301General Information ... 297High Speed ...

Trailer Weight ...330Transaxle ... 258Automatic ... 12,258Operation ...

Washer, Adding Fluid ... 362,363Washers, Windshield ... 139Washing Vehicle ... 393Weight Load C

NOTES

NOTES

To reattach the seat belt to the third row center seat, pullthe small (keyed buckle) latch plate forward from theheadliner slots and insert it into th

NOTES

NOTES

NOTES

Seat Belt PretensionersThe seat belts for both front seating positions areequipped with pretensioning devices that are designed toremove any slack fro

Enhanced Warning System (BeltAlert) will continue tochime and flash the Seat Belt Warning Light for 96seconds or until the driver’s seat belt is buckl

Failure to use driver and passenger seat belts providedis a major cause of severe or fatal injury. In fact, the U.S.government notes that the universa

4. Programming mode will be cancelled after the featurehas toggled with the seat belt still buckled or if theignition switch is turned to the lock pos

Driver And Right Front Passenger SupplementalRestraint System (SRS)—AirbagsThis vehicle has airbags for both the driver and rightfront passenger as a

WARNING!•Do not put anything on or around the front airbagcovers or attempt to manually open them. You maydamage the airbags and you could be injured

Here are some simple steps you can follow to minimizethe risk of harm from a deploying airbag.1. Children 12 years and under should always ridebuckled

WARNING!•Relying on the airbags alone could lead to moresevere injuries in a collision. The airbags workwith your seat belt to restrain you properly.

How the Airbag System Works•The Occupant Restraint Controller (ORC) determinesif a frontal collision is severe enough to require theairbags to inflate

•The Driver and Passenger Airbag/Inflator Units arelocated in the center of the steering wheel and the rightside of the instrument panel. When the ORC

The following requirements must be strictly adhered to:•Do not modify the front seat center console or centerposition seat in any way.•Do not use prio

However, if you haven’t healed significantly within afew days, or if you have any blistering, see your doctorimmediately. As the airbags deflate you m

Maintaining Your Airbag SystemWARNING!•Modifications to any part of the airbag system could cause it to failwhen you need it. You could be injured if

6 INTRODUCTION

•The light flickers or comes on and remains on whiledriving.NOTE: If the speedometer, tachometer or any enginerelated gauges are not working, the airb

may be released for incorporation in aggregate crashdatabases, such as those maintained by the US govern-ment and various states. Data of a potentiall

Child RestraintEveryone in your vehicle needs to be buckled up all thetime - babies and children, too. Every state in the UnitedStates and all Canadia

LATCH child restraint anchorage system. (See theLATCH - Child Seat Anchorage System section.)•Rearward-facing child seats must NEVER be used inthe fro

•If the shoulder belt contacts the face or neck, move thechild closer to the center of the vehicle. Never allow achild to put the shoulder belt under

around the child restraint so that it is not necessary touse a locking clip. If the seat belt has a cinching latchplate, pulling up on the shoulder po

and hooks for connection to the top tether anchorageshave been available for some time. For some older childrestraints, many child restraint manufactu

Installing the LATCH-Compatible Child RestraintSystemWe urge that you carefully follow the directions of themanufacturer when installing your child re

anchorages. Next attach the lower hooks or connectorsover the top of the anchorage bars, pushing aside the seatcover material. Then attach the tether

Installing Child Restraints Using the Vehicle SeatBeltThe second and third row seats have either cinching latchplates or automatic locking retractors

WARNINGS AND CAUTIONSThis manual contains WARNINGS against operatingprocedures which could result in an accident or bodilyinjury. It also contains CAU

WARNING!An incorrectly anchored tether strap could lead toincreased head motion and possible injury to thechild. Use only the anchor positions directl

WARNING!An incorrectly anchored tether strap could lead toseat failure and injury to the child. In a collision, theseat could come loose and allow the

A new engine may consume some oil during its first fewthousand miles of operation. This is a normal part of thebreak-in and is not an indication of di

Safety Checks You Should Make Inside TheVehicleHeater Defroster DuctsInspect the heater defroster ducts for proper operation.Check for proper air flow

LightsCheck the operation of all exterior lights. Check turnsignal and high beam indicator lights on the instrumentpanel.Door LatchesCheck for positiv

UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 Mirrors ...79▫ Inside Day/Night Mirror ...79▫ Automatic

䡵 Seats ...108▫ Front Seat Manual Seat Adjustment ...108▫ Front Seats Manual Seat Recliners ...109▫ Manual Lu

▫ Headlight Delay ...133▫ Automatic Headlights — If Equipped ...133▫ Headlights, Parking Lights, Panel Lights ...134▫ Illumin

▫ Dome/Reading Lights ...151▫ Electronic Vehicle Information Center (EVIC) —If Equipped ...152▫ Compass/Temperatu

MIRRORSInside Day/Night MirrorThe mirror should be adjusted to center on the viewthrough the rear window. A two-point pivot systemallows for horizonta

VEHICLE MODIFICATIONS / ALTERATIONSWARNING!Any modifications or alterations to this vehiclecould seriously affect its roadworthiness and safetyand may

Automatic Dimming Mirror — If EquippedThis mirror will automatically adjust for annoying head-light glare from vehicles behind you. You can turn thefe

CAUTION!To avoid damage to the mirror during cleaning,never spray any cleaning solution directly onto themirror. Apply the solution onto a clean cloth

To adjust a mirror, turn the control wand toward the leftor right mirror positions indicated. Tilt the control wandin the direction you want the mirro

Heated Mirrors — If EquippedHeated mirrors are automatically activated when youdepress the rear window defroster switch located on theinstrument panel

NOTE: The UConnect™ system use requires a cellularphone equipped with the Bluetooth ⬙Hands-Free Profile,⬙version 0.96 or higher. See www.chrysler.com/

The UConnect™ system can be used with any Hands-Free Profile certified Bluetooth™ cellular phone. Seewww.chrysler.com/uconnect for supported phones. I

•Prior to giving a voice command, one must wait forthe voice on beep, which follows the ⬙Ready⬙ promptor another prompt.•For certain operations, compo

Pair (Link) UConnect™ System to a Cellular PhoneTo begin using your UConnect™ system, you must pairyour compatible Bluetooth™ enabled cellular phone.N

•You will then be asked to give your cellular phone apriority level between 1 and 7, 1 being the highestpriority. You can pair up to seven cellular ph

Call/Dial by Saying a Name•Press the “Phone” button to begin.•After the ⬙Ready⬙ prompt and the following beep, say“Dial” or Call.⬙•System will prompt

THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A Word About Your Keys ...12▫ Ignition Key Removal ...12▫ Locking

After you are finished adding an entry into the phone-book, you will be given the opportunity to add morephone numbers to the current entry or to retu

Delete Entries in the UConnect™ PhonebookNOTE: Editing phonebook entries is recommendedwhen vehicle is not in motion.•Press the ’Phone’ button to begi

List All Names in the UConnect™ Phonebook•Press the ’Phone’ button to begin.•After the ⬙Ready⬙ prompt and the following beep, say⬙Phonebook List Names

Answer or Reject an Incoming Call - CallCurrently in ProgressIf a call is currently in progress and you have anotherincoming call, you will hear the s

Conference CallWhen two calls are in progress (one active and one onhold), press and hold the ’Phone’ button until you hear adouble beep indicating th

•After ignition key is switched to off, a call can continueon the UConnect™ system for certain duration, afterwhich the call is automatically transfer

•After the ⬙Ready⬙ prompt and the following beep, say⬙Emergency⬙ and the UConnect™ system will instructthe paired cellular phone to call the emergency

PagingTo learn how to page, refer to ⬙Working with AutomatedSystems.⬙ Paging works properly except for pagers ofcertain companies which time-out a lit

Turning Confirmation Prompts On/OffTurning confirmation prompts off will stop the systemfrom confirming your choices (e.g., the UConnect™system will n

Mute/Un-mute (Mute off)When you mute the UConnect™ system, you will still beable to hear the conversation coming from the otherparty, but the other pa