200Chrysler Group LLCOWNER’S MANUAL2014 20014C41-126-AC Third Edition Printed in U.S.A.
WARNING! (Continued)• Never place or install floor mats or other floorcoverings in the vehicle that cannot be properlysecured to prevent them from mov
Periodic Safety Checks You Should Make OutsideThe VehicleTiresExamine tires for excessive tread wear and uneven wearpatterns. Check for stones, nails,
UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 MIRRORS ...105▫ Inside Day/Night Mirror ...105▫ Automatic Di
䡵 SEATS ...146▫ Power Seats — If Equipped ...147▫ Heated Seats — If Equipped ...150▫ Manual Front Seat
▫ Daytime Running Lights (DRL) —If Equipped ...167▫ Instrument Panel Dimmer ...167▫ Map/Reading/Interior Lights ...
▫ Troubleshooting Tips ...185▫ General Information...186䡵 POWER SUNROOF — IF EQUIPPED ...187▫ Opening Sunroof —
MIRRORSInside Day/Night MirrorA two-point pivot system allows for horizontal andvertical mirror adjustment. Adjust the mirror to center onthe view thr
Automatic Dimming Mirror — If EquippedThis mirror automatically adjusts for headlight glarefrom vehicles behind you. You can turn the feature on oroff
CAUTION!To avoid damage to the mirror during cleaning, neverspray any cleaning solution directly onto the mirror.Apply the solution onto a clean cloth
THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A WORD ABOUT YOUR KEYS ...12▫ Ignition Key Removal ...12▫ Key-In-Igniti
When you are finished adjusting the mirror, turn thecontrol to the center position to prevent accidentallymoving a mirror.Adjusting Side View MirrorsO
WARNING! (Continued)collide with another vehicle or other object. Use yourinside mirror when judging the size or distance of avehicle seen in the pass
Uconnect® Phone — IF EQUIPPEDUconnect® Phone is a voice-activated, hands-free, in-vehicle communications system. Uconnect® Phone al-lows you to dial a
The Uconnect® Phone is driven through yourBluetooth® “Hands-Free Profile” mobile phone.Uconnect® features Bluetooth® technology - the globalstandard t
Voice Command ButtonActual button location may vary with the ra-dio. The individual buttons are described in the“Operation” section.The Uconnect® Phon
part of the command when you are asked for it. Forexample, you can use the compound form voice com-mand “Phonebook New Entry,” or you can break thecom
The following are general phone to Uconnect® Phonepairing instructions:1. Press thebutton to begin.2. After the “Ready” prompt and the following beep,
• The system will prompt you to say the number youwant to call.• For example, you can say “151-1234-5555.”• The Uconnect® Phone will confirm the phone
• Automatic download and update, if supported, beginsas soon as the Bluetooth® wireless phone connection ismade to the Uconnect® Phone, for example, a
• When prompted, enter the number designation (e.g.,“Home,” “Work,” “Mobile,” or “Other”). This willallow you to store multiple numbers for each phone
▫ Programming Additional Transmitters...26▫ Transmitter Battery Replacement ...26▫ General Information ...27䡵 REMOTE STA
After you are finished editing an entry in the phonebook,you will be given the opportunity to edit another entry inthe phonebook, call the number you
Delete/Erase “All” Uconnect® Phonebook Entries• Press the button to begin.• After the “Ready” prompt and the following beep, say“Phonebook Erase All.”
mobile service plan. For example, if your mobile serviceplan provides three-way calling, this feature can beaccessed through the Uconnect® Phone. Chec
Place/Retrieve A Call From HoldTo put a call on hold, press the button until you heara single beep. This indicates that the call is on hold. Tobring t
Redial• Press the button to begin.• After the “Ready” prompt and the following beep, say“Redial.”• The Uconnect® Phone will call the last number thatw
• After the “Ready” prompt and the following beep, saythe name of the language you wish to switch toEnglish, Espanol, or Francais.• Continue to follow
• If supported, this number may be programmable onsome systems. To do this, press thebutton and say“Setup,” followed by “Emergency.”• The Uconnect® Ph
Working With Automated SystemsThis method is used in instances where one generally hasto press numbers on the mobile phone keypad whilenavigating thro
• Some paging and voice mail systems have system timeout settings that are too short and may not allow theuse of this feature.Barge In — Overriding Pr
dialing a number with your paired Bluetooth® mobilephone, the audio will be played through your vehicle’saudio system. The Uconnect® Phone will work t
▫ Automatic Locking Retractor Mode (ALR) —If Equipped ...52▫ Energy Management Feature ...53▫ Seat Belt Pretensioner
Connect Or Disconnect Link Between TheUconnect® Phone And Mobile PhoneYour mobile phone can be paired with many differentelectronic devices, but can o
Uconnect® Phone will return to using the highestpriority phone present in or near (approximatelywithin 30 ft. [9 m]) the vehicle.Delete Uconnect® Phon
• Press thebutton and say the “Voice Training,”“System Training,” or “Start Voice Training” com-mand.You can either press the Uconnect® Phone button t
• Low-to-medium vehicle speed• Low road noise• Smooth road surface• Fully closed windows• Dry weather condition• Even though the system is designed fo
• Low Road Noise• Smooth Road Surface• Fully Closed Windows• Dry Weather Conditions• Operation From The Driver’s Seat• Performance, such as audio clar
3. Uconnect® Phone will play the new text message foryou.After reading a message, you can “Reply” or “Forward”the message using Uconnect® Phone.Send M
13. I’ll be late.14. Are you there yet?15. Where are we meeting?16. Can this wait?17. Bye for now.18. When can we meet?19. Send number to call.20. Sta
3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
3UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137
A WORD ABOUT YOUR KEYSThe authorized dealer that sold you your vehicle has thekey code numbers for your vehicle locks. These numberscan be used to ord
Voice CommandsPrimary Alternate (s)zeroonetwothreefourfivesixseveneightninestar (*)plus (+)pound (#)add locationVoice CommandsPrimary Alternate (s)all
Voice CommandsPrimary Alternate (s)helphomelanguagelist nameslist phonesmobilemutemute offnew entrynootherpair a phonephone pairing pairingphonebook p
General InformationThis device complies with Part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions:•
WARNING!Any voice commanded system should be used onlyin safe driving conditions following all applicablelaws, including laws regarding phone use. You
To hear the first available Menu, press the Voice Com-mandbutton and say “Help” or “Main Menu.”CommandsThe Voice Command system understands two types
• “Bluetooth Streaming” (to switch to Bluetooth®Streaming mode)• “Memo” (to switch to the memo recorder)• “System Setup” (to switch to system setup)Ra
• “Next Channel” (to select the next channel)• “Previous Channel” (to select the previous channel)• “List Channel” (to hear a list of available channe
Memo ModeTo switch to the voice recorder mode, say “Memo.” Inthis mode, you may say the following commands:• “New Memo” (to record a new memo) — Durin
• “Tutorial”• “Voice Training”NOTE: Keep in mind that you have to press the VoiceCommandbutton first and wait for the beepbefore speaking the “Barge I
WARNING! (Continued)• Do not allow people to ride in any area of yourvehicle that is not equipped with seats and seatbelts. In a collision, people rid
NOTE:• If you try to remove the key before you place the shiftlever in PARK, the key may become trapped tempo-rarily in the ignition switch lock cylin
WARNING!• Adjusting a seat while driving may be dangerous.Moving a seat while driving could result in loss ofcontrol which could cause a collision and
Tilting The Seat Up Or DownThe angle of the seat cushion can be adjusted in fourdirections. Pull upward or push downward on the frontor rear of the se
CAUTION!Do not place any article under a power seat orimpede its ability to move as it may cause damage tothe seat controls. Seat travel may become li
indicating the change. The LOW-level setting will turn OFFautomatically after approximately 30 minutes.WARNING!• Persons who are unable to feel pain t
Pull the bar upward to move the seat forward or rear-ward. Release the bar once the seat is in the positiondesired. Then, using body pressure, move fo
Reclining SeatsThe recline lever is located on the side of the seat. To recline,lean forward slightly before lifting the lever, then lean backto the d
Head RestraintsHead restraints are designed to reduce the risk of injuryby restricting head movement in the event of a rearimpact. Head restraints sho
between the back of the occupant’s head and the AHR.This system is designed to help prevent or reduce theextent of injuries to the driver and front pa
For comfort the Active Head Restraints can be tilted for-ward and rearward. To tilt the head restraint closer to theback of your head, pull forward on
• In the event of deployment of an Active Head Re-straint, refer to “Occupant Restraints/Resetting ActiveHead Restraints (AHR)” in “Things to Know Bef
• For vehicles equipped with the Electronic VehicleInformation Center (EVIC), the power windowswitches, radio, hands–free system (if equipped), andpow
Fold-Flat Passenger SeatbackThe recline handle on the front passenger seat alsoreleases the seatback to fold forward.The hard seatback features a work
Folding Rear SeatTo provide additional storage area, the rear seatback canbe folded forward. Pull on the loops to fold down eitheror both seatbacks.Wh
Folding Rear Seat Center ArmrestThe rear seat is equipped with a folding armrest withcupholders.TO OPEN AND CLOSE THE HOODTo open the hood, two latche
2. Then lift the secondary latch located under the frontedge of the hood, near the center and raise the hood.Use the hood prop rod to secure the hood
CAUTION!To prevent possible damage, do not slam the hood toclose it. Use a firm downward push at the center ofthe hood to ensure that both latches eng
Headlights And Parking LightsTurn the end of the multifunction lever to the first detentfor parking light operation. Turn to the second detent forhead
With the engine running and the multifunction lever inthe AUTO position, the headlights will turn on and turnoff based on the surrounding light levels
Turn SignalsMove the multifunction lever up or down and the arrowson each side of the instrument cluster flash to showproper operation of the front an
Flash-To-PassYou can signal another vehicle with your headlights bylightly pulling the multifunction lever toward you. Thiswill turn on the high beam
Daytime Running Lights (DRL) — If EquippedThe front turn signal lamps will turn on as DaytimeRunning Lights (DRL) whenever the ignition is ON, theengi
Key-In-Ignition ReminderOpening the driver’s door when the key is in the ignitionsounds a signal to remind you to remove the key.NOTE:• The Key-In-Ign
Map/Reading/Interior LightsThese lights are mounted between the sun visors abovethe rearview mirror. Each light can be turned on bypressing the barrel
because a door is open. To restore interior light operation,either turn the ignition switch ON or cycle the lightswitch.Battery Saver FeatureTo protec
NOTE: The wipers will automatically return to the parkposition if you turn the ignition switch OFF while theyare operating. The wipers will resume ope
regulate the wipe interval from a minimum of one cycleevery second to a maximum of approximately 18 secondsbetween cycles.NOTE: The wiper delay times
WARNING! (Continued)the windshield during freezing weather, warm thewindshield with defroster before and during wind-shield washer use.Mist FeaturePus
column) is placed in the AUTO position. In addition, theheadlights will turn off when the wipers are turned off ifthey were turned on by this feature.
WARNING!Do not adjust the steering column while driving.Adjusting the steering column while driving or driv-ing with the steering column unlocked, cou
NOTE: In order to ensure proper operation, the Elec-tronic Speed Control System has been designed to shutdown if multiple Speed Control functions are
To DeactivateA soft tap on the brake pedal, pushing the CANCELbutton, or normal brake pressure while slowing thevehicle will deactivate the Electronic
To Decrease SpeedWhen the Electronic Speed Control is set, you can de-crease speed by pushing the SET (-) button.The speed decrement shown is dependan
NOTE: A key which has not been programmed is alsoconsidered an invalid key even if it is cut to fit theignition switch lock cylinder for that vehicle.
WARNING!Electronic Speed Control can be dangerous where thesystem cannot maintain a constant speed. Your ve-hicle could go too fast for the conditions
NOTE: HomeLink® is disabled when the Vehicle Secu-rity Alarm is active.Before You Begin Programming HomeLink®Be sure that your vehicle is parked outsi
Programming A Rolling CodeFor programming garage door openers that were manu-factured after 1995. These garage door openers can beidentified by the “L
2.Place the hand-held transmitter 1 to 3 in (3 to 8 cm) awayfrom the HomeLink® button you wish to program whilekeeping the HomeLink® indicator light i
Reprogramming A Single HomeLink® ButtonTo reprogram a channel that has been previously trained,follow these steps:1. Cycle the ignition to the ON/RUN
• To program the two remaining HomeLink® buttons,repeat each step for each remaining button. DO NOTerase the channels.Reprogramming A Single HomeLink®
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)away from the HomeLink® button you wish to pro-gram while keeping the HomeLink® indicator ligh
3. Without releasing the button proceed with“Canadian/Gate Operator Programming” step 2 andfollow all remaining steps.Using HomeLink®To operate, press
WARNING!Vehicle exhaust contains carbon monoxide, a danger-ous gas. Do not run your vehicle in the garage whileprogramming the transceiver. Exhaust ga
NOTE:• The transmitter has been tested and it complies withFCC and IC rules. Changes or modifications not ex-pressly approved by the party responsible
CAUTION!Always remove the Sentry Key® from the vehicleand lock all doors when leaving the vehicle unat-tended.At the time of purchase, the original ow
WARNING!• Never leave children alone in a vehicle, or withaccess to an unlocked vehicle. Never leave the KeyFob in or near the vehicle, or in a locati
position. The sunroof will close fully and stop automati-cally. This is called “Express Close”. During ExpressClose operation, any movement of the swi
Wind BuffetingWind buffeting can be described as the perception ofpressure on the ears or a helicopter-type sound in theears. Your vehicle may exhibit
The instrument panel power outlet, located below theclimate control knobs, has power available only when theignition is ON. This power outlet will als
NOTE: To ensure proper operation a MOPAR® knoband element must be used.CAUTION!• Do not exceed the maximum power of 160 Watts (13Amps) at 12 Volts. If
WARNING!To avoid serious injury or death:• Only devices designed for use in this type of outletshould be inserted into any 12 Volt outlet.• Do not tou
CIGAR LIGHTER AND ASH RECEIVER — IFEQUIPPEDAn optional ash receiver is available from your autho-rized dealer and will fit in the center console front
Rear Seat Bottle HolderThere are built-in bottle holders located in both rear doortrim panels.WARNING!If containers of hot liquid are placed in the bo
STORAGEGlove CompartmentThe glove compartment is located on the right side of theinstrument panel. To open the glove compartment, pulloutward on the l
Two separate storage compartments are also locatedunderneath the armrest.The top compartment holds small items, such as a penand note pad, while the l
VEHICLES SOLD IN CANADAWith respect to any Vehicles Sold in Canada, the name ChryslerGroup LLC shall be deemed to be deleted and the name ChryslerCana
4. Insert a blank Sentry Key® into the ignition switch.Turn the ignition switch to the ON/RUN positionwithin 60 seconds. After 10 seconds, a single ch
NOTE:• A notch in the front of the console base allows for useof a cellular phone while it is plugged into the poweroutlet with the armrest latched do
WARNING! (Continued)• The cargo area in the rear of the vehicle (with therear seatbacks in the locked-up or folded downposition) should not be used as
Ski Pass-ThroughThere is a ski pass-through door located behind the rearseat armrest that allows longer items, such as snow skis,to be stored in the r
CAUTION!Failure to follow these cautions can cause damage tothe heating elements:• Use care when washing the inside of the rearwindow. Do not use abra
UNDERSTANDING YOUR INSTRUMENT PANELCONTENTS䡵 INSTRUMENT PANEL FEATURES ...206䡵 INSTRUMENT CLUSTER ...207䡵 INSTRUMENT CLUSTER DESC
䡵 SETTING THE ANALOG CLOCK ...236䡵 Uconnect® 730N/430/430N CD/DVD/HDD/NAV — IF EQUIPPED ...237▫ Operating Instructions (Voice
▫ List Or Browse Mode ...267▫ Bluetooth® Streaming Audio (BTSA) ...269䡵 STEERING WHEEL AUDIO CONTROLS —IF EQUIPPED ...
INSTRUMENT PANEL FEATURES1 — Air Outlet 6 — Radio 11 — Storage Compartment2 — Side Window Demister Outlet 7 — Passenger Airbag 12 — Climate Control3 —
INSTRUMENT CLUSTER4UNDERSTANDING YOUR INSTRUMENT PANEL 207
VEHICLE SECURITY ALARM — IF EQUIPPEDThe Vehicle Security Alarm monitors the doors and trunkfor unauthorized entry and ignition switch for unauthor-ize
INSTRUMENT CLUSTER DESCRIPTIONS1. Temperature GaugeThe temperature gauge shows engine coolant tempera-ture. Any reading below the red mark of the gaug
5. Low Fuel LightWhen the fuel level drops to approximately 2.0gallons (7.6 Liters), the fuel symbol will light anda single chime will sound.NOTE: Thi
flash or remain on continuously. Refer to “OccupantRestraints” in “Things To Know Before Starting YourVehicle” for further information.9. Oil Pressure
11. Brake Warning LightThis light monitors various brake functions,including brake fluid level and parking brakeapplication. If the brake light turns
off unless the parking brake is applied or a brake fault isdetected. If the light does not illuminate, have the lightinspected by an authorized dealer
The two trip odometers show individual trip mileage. Toswitch from odometer to trip odometers, press andrelease the Trip Odometer button. To reset a t
HOTOILWhen this message is displayed there is a engine oilover-temperature condition. When this condition occurs,the “HOTOIL” message will be displaye
the oil change indicator system (after performing thescheduled maintenance) perform the following proce-dure:1. Turn the ignition switch to the ON/RUN
17. Electronic Throttle Control (ETC) Indicator LightThis light informs you of a problem with theElectronic Throttle Control (ETC) system. If aproblem
21. Front Fog Light Indicator — If EquippedThis indicator will illuminate when the front foglights are on.22. Vehicle Security Light — If EquippedThis
or the power door locks are unlocked in any manner,the Vehicle Security Alarm will automatically disarm.NOTE:• During the 16-second arming period, if
running, a malfunction has been detected in the ESCsystem. If this light remains on after several ignitioncycles, and the vehicle has been driven seve
Accordingly, when the low tire pressure telltale illumi-nates, you should stop and check your tires as soon aspossible, and inflate them to the proper
CAUTION! (Continued)equipped on your vehicle. Undesirable system opera-tion or sensor damage may result when using re-placement equipment that is not
WARNING!A malfunctioning catalytic converter, as referencedabove, can reach higher temperatures than in normaloperating conditions. This can cause a f
28. High Beam IndicatorThis light indicates that the headlights are on highbeam. Pull the turn signal lever toward the steer-ing wheel to switch the h
Control ButtonsSTEP ButtonPress the STEP button located on the steering wheel toscroll through sub menus (i.e., Temperature, Trip Func-tions: Odometer
ELECTRONIC VEHICLE INFORMATION CENTER(EVIC) — IF EQUIPPEDThe Electronic Vehicle Information Center (EVIC) fea-tures a driver-interactive display that
The system allows the driver to select information bypressing the following buttons on the instrument panelswitch bank located below the climate contr
SELECT ButtonPress and release the SELECT Button to accepta selection. The SELECT Button also resetsvarious Trip Functions.Electronic Vehicle Informat
• Remote start aborted — Hood ajar• Remote start aborted — Trunk ajar• Remote start aborted — Fuel low• Remote start disabled — System fault• Oil Chan
If the Vehicle Security Alarm is armed and the batterybecomes disconnected the Vehicle Security Alarm willremain armed when the battery is reconnected
NOTE: If the indicator message illuminates when youstart the vehicle, the oil change indicator system did notreset. If necessary repeat this procedure
Compass DisplayCOMPASS ButtonThe compass heading indicates the directionthe vehicle is facing. Press and release thecompass button to display one of e
Manual Compass CalibrationIf the compass appears erratic or inaccurate, and thevariance has been properly set, you may wish to manu-ally recalibrate t
To Change Compass Variance:1. Turn the ignition switch to the ON position. Leave theshift lever in PARK.2. Press and release the MENU button until “Pe
Distance To Empty (DTE)Shows the estimated distance that can be traveled withthe fuel remaining in the tank. This estimated distance isdetermined by a
Elapsed TimeShows the total elapsed time of travel since the last reset.Elapsed time will increment when the ignition switch isin the RUN or START pos
Press and release the MENU button until “PersonalSettings” displays in the EVIC.Press and release the DOWN button to display thefollowing programmable
Flash Lamp With LockWhen ON is selected, the front and rear turn signals willflash when the doors are locked or unlocked with theRKE transmitter. This
Illumin. ApproachWhen this feature is selected, the headlights will activateand remain on for up to 90 seconds when the doors areunlocked with the rem
Uconnect® 730N/430/430N CD/DVD/HDD/NAV —IF EQUIPPEDRefer to your Uconnect® Supplement Manual for de-tailed operating instructions.Operating Instructio
REMOTE KEYLESS ENTRY (RKE) — IFEQUIPPEDThis system allows you to lock or unlock the doors, openthe trunk, or activate the Panic Alarm from distancesap
Power Switch/Volume Control (Rotary)Push the ON/VOLUME control knob to turn on theradio. Push the ON/VOLUME control knob a secondtime to turn off the
5. To exit, press any button/knob, or wait five seconds.RW/FFPressing the RW (Rewind) or FF (Fast Forward) buttonscauses the tuner to search for the n
Push the rotary TUNE/SCROLL control knob again toexit setting tone, balance, and fade.AM/FM ButtonPress the buttons to select either AM or FM mode.SET
Operation Instructions — CD MODE For CD AndMP3 Audio PlayNOTE:• The ignition switch must be in the ON or ACC positionto operate the radio.• This radio
CAUTION! (Continued)• Dual-media disc types (one side is a DVD, theother side is a CD) should not be used, and they cancause damage to the player.EJEC
AM/FM ButtonPress the button to select either AM or FM mode.SET/RND Button (Random Play Button)Press this button while the CD is playing to activateRa
display the file name and folder name, and will assigna number instead. With a maximum number of files,exceeding 20 folders will result in this displa
MPEG Specifi-cationSampling Fre-quency (kHz)Bit Rate (kbps)MPEG-1 AudioLayer 348, 44.1, 32 320, 256, 224,192, 160, 128,112, 96, 80, 64,56, 48, 40, 32M
To increase the speed of disc loading, it is recommendedto use CD-R media and single-session discs. To create asingle-session disc, enable the “Disc a
Uconnect® 130 WITH SATELLITE RADIOOperating Instructions — Radio ModeNOTE: The ignition switch must be in the ON or ACCposition to operate the radio.P
Remote Key Unlock, Driver Door/All Doors FirstPressThis feature lets you program the system to unlock eitherthe driver’s door or all doors on the firs
another selection. Holding either button will bypassstations without stopping, until you release it.Voice Command System (Radio) — If EquippedRefer to
3. After adjusting the hours, press the right side TUNE/SCROLL control knob to set the minutes. The minuteswill begin to blink.4. Adjust the minutes u
Push the rotary TUNE/SCROLL control knob a secondtime and MID will display. Turn the TUNE/SCROLLcontrol knob to the right or left to increase or decre
Program Type16-Digit CharacterDisplayClassical ClassiclClassic Rock Cls RockCollege CollegeCountry CountryForeign Language LanguageInformation InformJ
If a preset button is activated while in the Music Type(Program Type) mode, the Music Type mode will beexited and the radio will tune to the preset st
Every time a preset button is used, a correspondingbutton number will display.Buttons1-6These buttons tune the radio to the stations that youcommit to
CAUTION!• This CD player will accept 4–3/4 in (12 cm) discsonly. The use of other sized discs may damage theCD player mechanism.• Do not use adhesive
RW/FFPress and hold FF (Fast Forward) and the CD player willbegin to fast forward until FF is released or RW oranother CD button is pressed. The RW (R
The radio uses the following limits for file systems:• Maximum number of folder levels: 8• Maximum number of files: 255• Maximum number of folders. (T
use a 44.1 kHz sampling rate and a 192, 160, 128, 96 orVBR bit rates.MPEG Specifi-cationSampling Fre-quency (kHz)Bit Rate (kbps)MPEG-1 AudioLayer 348,
Flash Lights With LockThe feature will cause the turn signal lights to flash whenthe doors are locked or unlocked with the RKE transmit-ter. This feat
To increase the speed of disc loading, it is recommendedto use CD-R media and single-session discs. To create asingle-session disc, enable the “Disc a
NOTE: The AUX device must be turned on and thedevice’s volume set to the proper level. If the AUX audiois not loud enough, turn the device’s volume up
Electronic Serial Number/Sirius IdentificationNumber (ESN/SID)Please have the following information available whencalling:1. The Electronic Serial Num
• Dense tree coverage may interrupt reception in theform of short audio mutes.• Driving under wide bridges or along tall buildings cancause intermitte
TUNE Control (Rotary)Turn the rotary TUNE/SCROLL control knob clockwiseto increase or counterclockwise to decrease the channel.MUSIC TYPE ButtonPressi
You may add a second channel to each pushbutton byrepeating the above procedure with this exception: Pressthe SET button twice and SET 2 will show in
Connecting The iPod® Or External USB DeviceUse the connection cable to connect an iPod® or externalUSB device to the vehicle’s USB connector port whic
• The audio device can be controlled using the radiobuttons to Play, Browse, and List the iPod® contents.• The audio device battery charges when plugg
• A single press backward << RW or forward FF>> willjump backward or forward respectively, for five sec-onds.• Use the << SEEK and S
List Or Browse ModeDuring Play mode, pressing any of the buttons describedbelow, will bring up List mode. List mode enablesscrolling through the list
equipped with EVIC. For details, refer to “ElectronicVehicle Information Center (EVIC)/Personal Settings(Customer-Programmable Features)” in “Understa
• Pressing a PRESET button will display the current liston the top line and the first item in that list on thesecond line.• To exit List mode without
Bluetooth® Streaming Audio (BTSA)Music can be streamed from your cellular phone to theUconnect® phone system.Controlling BTSA Using Radio ButtonsTo en
Previous TrackUse the SEEK DOWN button, or press the VR button onthe radio and say “Previous Track,” to jump to theprevious music track on your cellul
The remote sound system controls are located on the rearsurface of the steering wheel, at the three and nineo’clock positions.The right-hand rocker sw
CD/DVD DISC MAINTENANCETo keep a CD/DVD in good condition, take the followingprecautions:1. Handle the disc by its edge; avoid touching thesurface.2.
CLIMATE CONTROLSThe air conditioning and heating system is designed tomake you comfortable in all types of weather.Manual Heating And Air Conditioning
Temperature ControlRotate this control to regulate the tem-perature of the air inside the passengercompartment. Rotating the dial leftinto the blue ar
• ECONOMY MODEIf economy mode is desired, press the A/C button to turnOFF the indicator light and the A/C compressor. Then,select Panel, Bi-Level or F
• FloorAir is directed through the floor outlets with asmall amount flowing through the defrost andside window demist outlets.• MixAir is directed thr
• The use of the Recirculation mode in cold or dampweather will cause windows to fog on the inside,because of moisture buildup inside the vehicle. Sel
NOTE: If there is no key in the ignition switch, pressingthe LOCK button on the RKE transmitter while you are inthe vehicle will activate the Vehicle
Automatic OperationThe Automatic Temperature Control system automati-cally maintains the climate in the cabin of the vehicle atthe comfort levels desi
NOTE:• The temperature setting can be adjusted at anytimewithout affecting automatic operation.• Pressing the Air Conditioning Control button while in
280 UNDERSTANDING YOUR INSTRUMENT PANEL
The operator can override the AUTO mode setting tochange airflow distribution by rotating the Mode Controlknob (on the right) to one of the following
• Air Conditioner ControlPress this button to turn on the airconditioning during manual operationonly. When the air conditioning isturned on, cool deh
• Most of the time, when in Automatic Operation, youcan temporarily put the system into RecirculationMode by pressing the Recirculation button. Howeve
coolant that meets the requirements of Chrysler MaterialStandard MS-12106 and 50% water is recommended.Refer to “Maintenance Procedures” in “Maintaini
Outside Air IntakeMake sure the air intake, located directly in front of thewindshield, is free of obstructions such as leaves. Leavescollected in the
Control Setting Suggestions For Various Weather Conditions286 UNDERSTANDING YOUR INSTRUMENT PANEL
STARTING AND OPERATINGCONTENTS䡵 STARTING PROCEDURES ...291▫ Automatic Transmission ...291▫ Normal Starting...
1. With the RKE transmitter buttons facing down, use aflat blade screwdriver to pry the two halves of the RKEtransmitter apart. Make sure not to damag
䡵 DRIVING THROUGH WATER ...317▫ Flowing/Rising Water ...317▫ Shallow Standing Water ...317䡵 POWER STEERING ...
▫ Run Flat Tires — If Equipped ...347▫ Spare Tires — If Equipped ...348▫ Tire Spinning ...350▫ Tread Wear I
▫ Starting ...371▫ Cruising Range ...371▫ Replacement Parts ...371▫ Maintenance ...
STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust theinside and outside mirrors, fasten your seat belt, and ifpresent, instruc
CAUTION!Damage to the transmission may occur if the follow-ing precautions are not observed:• Do not shift from REVERSE, PARK, or NEUTRALinto any forw
Extreme Cold Weather (Below –20°F Or −29°C)To ensure reliable starting at these temperatures, use ofan externally powered electric engine block heater
the way to the floor and hold it there while cranking theengine. This should clear any excess fuel in case theengine is flooded.CAUTION!To prevent dam
After StartingThe idle speed is controlled automatically and it willdecrease as the engine warms up.ENGINE BLOCK HEATER — IF EQUIPPEDThe engine block
CAUTION! (Continued)• Do not shift between PARK, REVERSE, NEU-TRAL, or DRIVE when the engine is above idlespeed.• Before shifting into any gear, make
WARNING! (Continued)• Unintended movement of a vehicle could injurethose in and near the vehicle. As with all vehicles,you should never exit a vehicle
TABLE OF CONTENTSSECTION PAGE1INTRODUCTION ...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: Changes or modifications not expressly approvedby the party responsible for compliance could void theuser’s authority to operate the equipment.I
when the ignition is in the LOCK position, and onceremoved, the transmission is locked in PARK.NOTE: If a malfunction occurs, the system will trap the
Gear RangesDO NOT race the engine when shifting from PARK orNEUTRAL into another gear range.NOTE: After selecting any gear range, wait a moment toallo
WARNING! (Continued)• It is dangerous to shift out of PARK or NEUTRALif the engine speed is higher than idle speed. Ifyour foot is not firmly pressing
WARNING! (Continued)• When leaving the vehicle, always remove the igni-tion key and lock your vehicle. Never leave chil-dren alone in a vehicle, or wi
• Look at the transmission gear position display andverify that it indicates the PARK position.• With brake pedal released, verify that the shift leve
DRIVE (D)This range should be used for most city and highwaydriving. It provides the smoothest upshifts and down-shifts, and the best fuel economy. Th
will improve performance and extend transmission lifeby reducing excessive shifting and heat build-up. The ⬙3⬙range should also be used when descendin
NOTE: Even if the transmission can be reset, we recom-mend that you visit your authorized dealer at yourearliest possible convenience. Your authorized
NOTE: The torque converter clutch will not engage untilthe transmission fluid and engine coolant are warm[usually after 1 to 3 miles (2 to 5 km) of dr
Gear RangesDO NOT race the engine when shifting from PARK orNEUTRAL into another gear range.NOTE: After selecting any gear range, wait a moment toallo
• System not disabled from previous remote start event• Vehicle Security Alarm not activeWARNING!• Do not start or run an engine in a closed garage or
downhill grade and away from the curb on an uphillgrade.WARNING!• Never use the PARK position as a substitute for theparking brake. Always apply the p
WARNING! (Continued)• Unintended movement of a vehicle could injurethose in or near the vehicle. As with all vehicles,you should never exit a vehicle
CAUTION!• Before moving the shift lever out of PARK, youmust turn the ignition switch from the LOCK/OFFposition to the ON/RUN position, and also press
WARNING!Do not coast in NEUTRAL and never turn off theignition to coast down a hill. These are unsafepractices that limit your response to changing tr
temperature as well as vehicle speed. This feature im-proves warm up time of the engine and transmission toachieve maximum efficiency. Engagement of t
NOTE: Even if the transmission can be reset, we recom-mend that you visit your authorized dealer at yourearliest possible convenience. Your authorized
NOTE: The torque converter clutch will not engage untilthe transmission fluid and engine coolant are warm(usually after 1 to 3 miles [2 to 5 km] of dr
• You can start out, from a stop, in any gear except topgear. Tapping (+) (at a stop) will allow starting insecond gear. Starting out in second gear i
DRIVING ON SLIPPERY SURFACESAccelerationRapid acceleration on snow covered, wet, or other slip-pery surfaces may cause the driving wheels to pullerrat
DRIVING THROUGH WATERDriving through water more than a few inches/centimeters deep will require extra caution to ensuresafety and prevent damage to yo
To Enter Remote Start ModePress and release the REMOTE START buttonon the RKE transmitter twice within five sec-onds. The vehicle doors will lock, the
CAUTION!• Always check the depth of the standing waterbefore driving through it. Never drive throughstanding water that is deeper than the bottom ofth
POWER STEERINGThe standard power steering system will give you goodvehicle response and increased ease of maneuverabilityin tight spaces. The system w
CAUTION!Do not use chemical flushes in your power steeringsystem as the chemicals can damage your powersteering components. Such damage is not covered
possible. To release the parking brake, pull the lever upslightly, press the center button, then lower the levercompletely.When the parking brake is a
WARNING! (Continued)• Never leave children alone in a vehicle, or withaccess to an unlocked vehicle. Allowing children tobe in a vehicle unattended is
computer to modulate the hydraulic pressure to preventwheel lock-up and avoid skidding on slippery surfaces.WARNING!• Pumping of the anti-lock brakes
If the “Anti-Lock Brake Warning Light” is on, the brakesystem should be serviced as soon as possible to restorethe benefits of anti-lock brakes. If th
WARNING!The Anti-Lock Brake System contains sophisticatedelectronic equipment that may be susceptible tointerference caused by improperly installed or
WARNING! (Continued)very slippery surfaces, or hydroplaning. The capa-bilities of an ABS-equipped vehicle must never beexploited in a reckless or dang
WARNING!• The BAS cannot prevent the natural laws of phys-ics from acting on the vehicle, nor can it increasebraking efficiency beyond that afforded b
To Exit Remote Start Mode Without Driving TheVehiclePress and release the REMOTE START button one time orallow the engine to run for the entire 15 min
WARNING!Electronic Stability Control (ESC) cannot prevent thenatural laws of physics from acting on the vehicle, norcan it increase the traction affor
intended to be used if the vehicle is in deep snow, sand,or gravel conditions and more wheel spin than ESCwould normally allow is required to gain tra
NOTE: To improve the vehicle’s traction when drivingwith snow chains, or starting off in deep snow, sand orgravel, it may be desirable to switch to th
• Each time the ignition is cycled ON, the ESC systemwill be ON even if it was cycled off previously.• The ESC system will make buzzing or clicking so
NOTE:• P (Passenger) - Metric tire sizing is based on U.S.design standards. P-Metric tires have the letter “P”molded into the sidewall preceding the s
Tire Sizing ChartEXAMPLE:Size Designation:P = Passenger car tire size based on U.S. design standardsⴖ...blank...ⴖ = Passenger car tire based on Euro
EXAMPLE:Service Description:95 = Load Index— A numerical code associated with the maximum load a tire can carryH = Speed Symbol—A symbol indicating th
Tire Identification Number (TIN)The TIN may be found on one or both sides of the tire,however, the date code may only be on one side. Tires withwhite
Tire Terminology And DefinitionsTerm DefinitionB-Pillar The vehicle B-Pillar is the structural member of the body locatedbehind the front door.Cold Ti
Tire Loading And Tire PressureTire And Loading Information Placard LocationNOTE: The proper cold tire inflation pressure is listed onthe driver’s side
WARNING!• For personal security and safety in the event of ancollision, lock the vehicle doors as you drive aswell as when you park and leave the vehi
Tire And Loading Information PlacardThis placard tells you important information about the:1. Number of people that can be carried in the vehicle.2. T
To determine the maximum loading conditions of yourvehicle, locate the statement “The combined weight ofoccupants and cargo should never exceed XXX lb
NOTE:• If your vehicle will be towing a trailer, load from yourtrailer will be transferred to your vehicle. The follow-ing table shows examples on how
5STARTING AND OPERATING 341
WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti
WARNING! (Continued)• Unequal tire pressures from one side of the vehicleto the other can cause the vehicle to drift to theright or left.• Always driv
CAUTION!After inspecting or adjusting the tire pressure, al-ways reinstall the valve stem cap. This will preventmoisture and dirt from entering the va
loading may be required for high-speed vehicle opera-tion. Refer to your authorized tire dealer or originalequipment vehicle dealer for recommended sa
Consult an authorized tire dealer for tire repairs andadditional information.Damaged Run Flat tires, or Run Flat tires that haveexperienced a loss of
If you need snow tires, select tires equivalent in size andtype to the original equipment tires. Use snow tires onlyin sets of four; failure to do so
Automatic Door Locks — If EquippedThe auto door lock feature default condition is enabled.When enabled, the door locks will lock automaticallywhen the
Spare Tires — If EquippedNOTE: For vehicles equipped with TIREFIT instead of aspare tire, please refer to “TIREFIT KIT” in “What To DoIn Emergencies”
Do not install a wheel cover or attempt to mount aconventional tire on the compact spare wheel, since thewheel is designed specifically for the compac
WARNING!Limited-use spares are for emergency use only. In-stallation of this limited-use spare tire affects vehiclehandling. With this tire, do not dr
These indicators are molded into the bottom of the treadgrooves. They will appear as bands when the tread depthbecomes 1/16 in (2 mm). When the tread
WARNING!Tires and the spare tire should be replaced after sixyears, regardless of the remaining tread. Failure tofollow this warning can result in sud
WARNING!• Do not use a tire, wheel size or rating other thanthat specified for your vehicle. Some combinationsof unapproved tires and wheels may chang
TIRE ROTATION RECOMMENDATIONSThe tires on the front and rear of your vehicle operate atdifferent loads and perform different steering, driving,and bra
TIRE PRESSURE MONITOR SYSTEM (TPMS)The Tire Pressure Monitor System (TPMS) will warn thedriver of a low tire pressure based on the vehicle recom-mende
to be driven for up to 20 minutes above 15 mph(24 km/h) in order for the TPMS to receive this informa-tion.For example, your vehicle may have a recomm
CAUTION! (Continued)• After inspecting or adjusting the tire pressure,always reinstall the valve stem cap. This willprevent moisture and dirt from ent
Auto Unlock On Exit ProgrammingThe Automatic Unlock Doors On Exit feature can beenabled or disabled as follows:• For vehicles equipped with the Electr
monitor tire pressure levels. Sensors, mounted to eachwheel as part of the valve stem, transmit tire pressurereadings to the Receiver Module.NOTE: It
“Tire Pressure Monitoring Telltale Light” will turn offwhen the fault condition no longer exists. A system faultcan occur due to any of the following:
4. For each subsequent ignition key cycle, a chime willsound and the “Tire Pressure Monitoring TelltaleLight” will flash on and off for 75 seconds and
Tire Pressure Monitoring Low Pressure WarningsThe “Tire Pressure Monitoring Telltale Light” willilluminate in the instrument cluster and a chime wills
2. Installing some form of aftermarket window tintingthat affects radio wave signals.3. Lots of snow or ice around the wheels or wheelhousings.4. Usin
4. For each subsequent ignition key cycle, a chime willsound, the “Tire Pressure Monitoring Telltale Light”will flash on and off for 75 seconds and th
FUEL REQUIREMENTSThis engine is designed to meet all emissionsregulations and provide excellent fueleconomy and performance when using high-quality un
Gasoline/Oxygenate BlendsSome fuel suppliers blend unleaded gasoline with oxy-genates such as Ethanol. Fuels blended with oxygenatesmay be used in you
• Disconnect and reconnect the battery to reset theengine controller memory.More extensive repairs will be required for prolongedexposure to E-85 fuel
CAUTION! (Continued)• An out-of-tune engine or certain fuel or ignitionmalfunctions can cause the catalytic converter tooverheat. If you notice a pung
The Child-Protection Door Locks are located inside therear edge of the door. Insert the tip of the ignition key orsimilar flat-bladed object into the
WARNING! (Continued)• Guard against carbon monoxide with proper main-tenance. Have the exhaust system inspected everytime the vehicle is raised. Have
Ethanol Fuel (E-85)E-85 is a mixture of approximately 85% fuel ethanol and15% unleaded gasoline.WARNING!Ethanol vapors are extremely flammable and cou
For best results, a refueling pattern that avoids alternat-ing between E-85 and unleaded gasoline is recom-mended.When you do switch fuel types it is
StartingThe characteristics of E-85 fuel make it unsuitable for usewhen ambient temperatures fall below 0°F (-18°C). In therange of 0°F (-18°C) to 32°
ADDING FUELFuel Filler Cap (Gas Cap)The gas cap is behind the fuel filler door, on the left rearquarter panel of the vehicle. If the gas cap is lost o
After removing the gas cap, place the gas cap tether cableover a hook on the inside of the fuel door. This keeps the gascap suspended away from and pr
WARNING!• Never have any smoking materials lit in or near thevehicle when the gas cap is removed or the tank isbeing filled.• Never add fuel when the
VEHICLE LOADINGVehicle Certification LabelYour vehicle has a Vehicle Certification Label affixed tothe drivers side B-Pillar or the rear of the driver
OverloadingThe load carrying components (axle, springs, tires,wheels, etc.) of your vehicle will provide satisfactoryservice as long as you do not exc
To maintain the New Vehicle Limited Warranty coverage,follow the requirements and recommendations in thismanual concerning vehicles used for trailer t
NOTE: For emergency exit with the system engaged,pull the lock knob up (UNLOCKED position), roll downthe window, and open the door with the outside do
WARNING!It is important that you do not exceed the maximumfront or rear GAWR. A dangerous driving conditioncan result if either rating is exceeded. Yo
Trailer Hitch ClassificationThe following chart provides the industry standard forthe maximum trailer weight a given trailer hitch class cantow and sh
Trailer Towing Weights (Maximum Trailer Weight Ratings)The following chart provides the maximum trailer weight ratings towable for your given drivetra
Trailer And Tongue WeightAlways load a trailer with 60% to 65% of the weight inthe front of the trailer. This places 10% to 15% of theGross Trailer We
NOTE: Remember that everything put into or on thetrailer adds to the load on your vehicle. Also, additionalfactory-installed options or dealer-install
WARNING!Improper towing can lead to a collision. Follow theseguidelines to make your trailer towing as safe aspossible:• Make certain that the load is
WARNING! (Continued)• Total weight must be distributed between the towvehicle and the trailer such that the following fourratings are not exceeded:1.
Towing Requirements — Trailer Brakes• Do not interconnect the hydraulic brake system orvacuum system of your vehicle with that of the trailer.This cou
CAUTION!If the trailer weighs more than 1,000 lbs (454 kg)loaded, it should have its own brakes and theyshould be of adequate capacity. Failure to do
Towing TipsBefore setting out on a trip, practice turning, stopping,and backing up the trailer in an area located away fromheavy traffic.Automatic Tra
WARNING!Never leave children unattended in a vehicle, and donot let children play with power windows. Do notleave the Key Fob in or near the vehicle,
If you REGULARLY TOW a trailer for more than 45minutes of continuous operation, then change the auto-matic transmission fluid and filter as specified
Cooling SystemTo reduce potential for engine and transmission over-heating, take the following actions:City DrivingWhen stopped for short periods of t
Recreational Towing — All ModelsRecreational towing is allowed ONLY if the front wheelsare OFF the ground. This may be accomplished using atow dolly o
WHAT TO DO IN EMERGENCIESCONTENTS䡵 HAZARD WARNING FLASHERS ...392䡵 IF YOUR ENGINE OVERHEATS ...392▫ Engine Oil Overheating (2.4L Engi
HAZARD WARNING FLASHERSThe Hazard Warning flasher switch is located on theinstrument panel, below the radio.Press the switch to turn on the Hazard War
NOTE: There are steps that you can take to slow downan impending overheat condition:• If your air conditioner (A/C) is on, turn it off. The A/Csystem
WHEEL AND TIRE TORQUE SPECIFICATIONSProper lug nut/bolt torque is very important to ensurethat the wheel is properly mounted to the vehicle. Anytime a
Tighten the lug nuts/bolts in a star pattern until eachnut/bolt has been tightened twice.After 25 miles (40 km) check the lug nut/bolt torque to besur
WARNING! (Continued)• Being under a jacked-up vehicle is dangerous. Thevehicle could slip off the jack and fall on you. Youcould be crushed. Never put
Preparations For Jacking1. Park the vehicle on a firm, level surface. Avoid ice orslippery areas.WARNING!Do not attempt to change a tire on the side o
Auto Window Up With Anti-Pinch Protection — IfEquippedLift the window switch fully upward to the seconddetent, release, and the window will go up auto
Jacking InstructionsWARNING!Carefully follow these tire changing warnings tohelp prevent personal injury or damage to yourvehicle:• Always park on a f
CAUTION!Do not attempt to raise the vehicle by jacking onlocations other than those indicated in the JackingInstructions for this vehicle.NOTE: Refer
2.Loosen, but do not remove, the wheel nuts by turningthem to the left one turn while the wheel is still on theground.CAUTION!Do not attempt to raise
4. Turn the jack screw to the left until the jack can beplaced under the jacking location. Once the jack ispositioned, turn the jack screw to the righ
WARNING!Raising the vehicle higher than necessary can makethe vehicle less stable. It could slip off the jack andhurt someone near it. Raise the vehic
5. Raise the vehicle by turning the jack screw to the right,using the jack handle. Raise the vehicle only until thetire just clears the surface and en
WARNING!•To avoid the risk of forcing the vehicle off the jack,do not tighten the lug nuts fully until the vehiclehas been lowered. Failure to follow
Road Tire InstallationVehicles Equipped With Wheel Covers1. Mount the road tire on the axle.2. To ease the installation process for steel wheels withw
3. Align the valve notch in the wheel cover with thevalve stem on the wheel. Install the cover by hand,snapping the cover over the two lug nuts. Do no
WARNING!To avoid the risk of forcing the vehicle off the jack,do not tighten the wheel nuts fully until the vehiclehas been lowered. Failure to follow
Reset Auto UpShould the Auto Up feature stop working, the windowprobably needs to be reset. To reactivate the Auto Upfeature, pull the window switch u
CAUTION!Do not use a portable battery booster pack or anyother booster source with a system voltage greaterthan 12 Volts or damage to the battery, sta
WARNING!• Take care to avoid the radiator cooling fan when-ever the hood is raised. It can start anytime theignition switch is ON. You can be injured
4. If using another vehicle to jump-start the battery, parkthe vehicle within the jumper cables reach, set theparking brake and make sure the ignition
WARNING!Do not connect the jumper cable to the negative (-)post of the discharged battery. The resulting electri-cal spark could cause the battery to
CAUTION!Accessories plugged into the vehicle power outletsdraw power from the vehicle’s battery, even when notin use (i.e., cellular phones, etc.). Ev
CAUTION!• When “rocking” a stuck vehicle by shifting be-tween DRIVE and REVERSE, do not spin thewheels faster than 15 mph (24 km/h), or drivetraindama
4. Turn the ignition to the ACC or ON/RUN position,but do not start the engine.5. Press and maintain firm pressure on the brake pedal.6. Insert a scre
Proper towing or lifting equipment is required to preventdamage to your vehicle. Use only tow bars and otherequipment designed for this purpose, follo
• The towing distance must not exceed 15 mi (24 km).• The towing speed must not exceed 25 mph (40 km/h).If the transmission is not operable, or the ve
MAINTAINING YOUR VEHICLECONTENTS䡵 ENGINE COMPARTMENT — 2.4L ...419䡵 ENGINE COMPARTMENT — 3.6L ...420䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II
open or partially open positions. This is a normal occur-rence and can be minimized. If the buffeting occurs withthe rear windows open, then open the
▫ Brake System ...444▫ Automatic Transmission ...446▫ Appearance Care And Protection FromCorrosion ...
ENGINE COMPARTMENT — 2.4L1 — Engine Coolant Reservoir 5 — Integrated Power Module (Fuses) 9 — Coolant Pressure Cap2 — Power Steering Fluid Reservoir 6
ENGINE COMPARTMENT — 3.6L1 — Engine Coolant Reservoir 5 — Air Cleaner Filter2 — Power Steering Fluid Reservoir 6 — Engine Oil Dipstick3 — Brake Fluid
ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor
persists, the message will appear the next time thevehicle is started. This might indicate a damaged cap. Ifthe problem is detected twice in a row, th
3. Approximately 15 seconds later, one of two things willhappen:• The MIL will flash for about 10 seconds and thenreturn to being fully illuminated un
available which include detailed service information foryour vehicle. Refer to these Service Manuals beforeattempting any procedure yourself.NOTE: Int
CAUTION! (Continued)• Your vehicle has been built with improved fluidsthat protect the performance and durability of yourvehicle and also allow extend
CAUTION!Do not overfill the engine. Overfilling the enginewill cause oil aeration, which can lead to loss of oilpressure and an increase in oil temper
CAUTION!Do not use chemical flushes in your engine oil as thechemicals can damage your engine. Such damage isnot covered by the New Vehicle Limited Wa
TRUNK SAFETY WARNINGWARNING!Do not allow children to have access to the trunk,either by climbing into the trunk from outside, orthrough the inside of
Synthetic Engine OilsYou may use synthetic engine oils provided the recom-mended oil quality requirements are met, and the recom-mended maintenance in
WARNING!The air induction system (air cleaner, hoses, etc.) canprovide a measure of protection in the case of enginebackfire. Do not remove the air in
WARNING!• Battery fluid is a corrosive acid solution and canburn or even blind you. Do not allow battery fluidto contact your eyes, skin, or clothing.
of the condenser fins and a performance test. Drive belttension should also be checked at this time.WARNING!• Use only refrigerants and compressor lub
A/C Air Filter — If EquippedRefer to the “Maintenance Schedule” for the propermaintenance intervals.WARNING!Do not remove the A/C air filter while the
6. Remove the A/C Air Filter by pulling it straight out ofthe housing.7.Install the A/C Air Filter with the arrow on the filterpointing toward the flo
operation and to protect against rust and wear. Prior tothe application of any lubricant, the parts concernedshould be wiped clean to remove dust and
reservoir with windshield washer solvent (not radiatorantifreeze) and operate the system for a few seconds toflush out the residual water.When refilli
WARNING!• Exhaust gases can injure or kill. They containcarbon monoxide (CO), which is colorless andodorless. Breathing it can make you unconsciousand
Under normal operating conditions, the catalytic con-verter will not require maintenance. However, it is im-portant to keep the engine properly tuned
• Advanced Front Air Bags for driver and front passen-ger• Supplemental Active Head Restraints (AHR) locatedon top of the front seats (integrated into
Cooling SystemWARNING!• When working near the radiator cooling fan,disconnect the fan motor lead or turn the ignitionswitch to the LOCK position. The
Refer to the “Maintenance Schedule” for the propermaintenance intervals.NOTE: Some vehicles require special tools to add coolantproperly. Failure to f
CAUTION! (Continued)• Do not use water alone or alcohol-based enginecoolant (antifreeze) products. Do not use additionalrust inhibitors or antirust pr
• Use only high purity water such as distilled or deion-ized water when mixing the water/engine coolant(antifreeze) solution. The use of lower quality
WARNING!• Do not open hot engine cooling system. Never addengine coolant (antifreeze) when the engine isoverheated. Do not loosen or remove the cap to
The radiator normally remains completely full, so there isno need to remove the radiator cap unless checking forengine coolant (antifreeze) freeze poi
• Keep the front of the radiator clean. If your vehicle isequipped with air conditioning, keep the front of thecondenser clean.•Do not change the ther
Overfilling of fluid is not recommended because it maycause leaking in the system.Fluid level can be expected to fall as the brake pads wear.Brake flu
WARNING! (Continued)• To avoid contamination from foreign matter ormoisture, use only new brake fluid or fluid that hasbeen in a tightly closed contai
NOTE: No chemical flushes should be used in anytransmission; only the approved lubricant should beused.CAUTION!Using a transmission fluid other than t
Here are some simple steps you can take to minimize therisk of harm from a deploying air bag:1. Children 12 years old and under should always ridebuck
2. Run the engine at normal idle speed for at least 60seconds, and leave the engine running for the rest ofthis procedure.3. Fully apply the parking b
To prevent dirt and water from entering the transmissionafter checking or replenishing fluid, make sure that thedipstick cap is properly reseated.CAUT
Fluid And Filter ChangesRefer to the ⬙Maintenance Schedule⬙ for the propermaintenance intervals. In addition, change the fluid andfilter if the fluid
Washing• Wash your vehicle regularly. Always wash your ve-hicle in the shade using MOPAR® Car Wash, or a mildcar wash soap, and rinse the panels compl
• If your vehicle is damaged due to a collision or similarcause that destroys the paint and protective coating,have your vehicle repaired as soon as p
Cleaning HeadlightsYour vehicle is equipped with plastic headlights and foglights that are lighter and less susceptible to stone breakagethan glass he
Interior CareInstrument Panel CoverThe instrument panel cover has a low glare surface, whichminimizes reflections in the windshield. Do not use pro-te
Glass SurfacesAll glass surfaces should be cleaned on a regular basiswith MOPAR® Glass Cleaner, or any commercialhousehold-type glass cleaner. Never u
Cleaning Center Console CupholdersRemovalGrab the rubber portion of the cupholder and lift up-ward.CleaningSoak the rubber cupholder liner in a mixtur
WARNING! (Continued)• If a general protection fuse for safety systems (airbag system, braking system), power unit systems(engine system, gearbox syste
5. If the air bag system in this vehicle needs to bemodified to accommodate a disabled person, contactthe Customer Center. Phone numbers are providedu
CavityCar-tridgeFuseMiniFuseDescription2 — 20 AmpYellowBrake VacuumPump3 — 10 AmpRedCenter HighMounted StopLight (CHMSL)/Brake Switch4 — 10 AmpRedIgni
CavityCar-tridgeFuseMiniFuseDescription12 — 20 AmpYellowSpare13 — 20 AmpYellowIgnition/CigarLighter14 — 10 AmpRedInstrument Panel15 40 AmpGreen— Radia
CavityCar-tridgeFuseMiniFuseDescription22 — 10 AmpRedIgnition Run – Cli-mate Controls/HotCupholder – IfEquipped23 — 15 AmpLt. BlueAuto Shutdown(ASD) R
CavityCar-tridgeFuseMiniFuseDescription30 — 20 AmpYellowIgnition Run –Heated Seats – IfEquipped31 — — Spare32 30 AmpPink— Auto Shutdown(ASD) Relay 133
CavityCar-tridgeFuseMiniFuseDescription36 30 AmpPink— Passenger DoorModule (PDM)/Driver Door Mod-ule (DDM)37 — 25 AmpNaturalPower Top Module– If Equip
VEHICLE STORAGEIf you will not be using your vehicle for more than 21days, you may want to take steps to preserve yourbattery.• Disengage the mini-fus
Exterior BulbsBulb NumberBi-Halogen Headlamp HIR2Front Turn Signal Lamp 3157NAKFront Park Lamp LED (Serviced at Autho-rized Dealer)Front Fog Lamp H11C
2. To begin removal of the driver side headlamp, reach inthrough the inner fender or from the engine compart-ment and grasp the bulb cover.1 — Headlam
3. Rotate bulb cover and one-quarter turn and pulloutward from assembly.4. Rotate bulb and connector one-quarter turn and pulloutward from assembly.CA
6. If the bulb comes in contact with any oily surface,wipe the bulb with a clean cloth and rubbing alcohol.7. Reinsert the bulb and socket assembly an
Buckle up even though you are an excellent driver, evenon short trips. Someone on the road may be a poor driverand cause a collision that includes you
Front Fog LampNOTE: Access to the lamps through the lower fasciacutout is limited. We recommend you access the lamps byturning the steering wheel to a
NOTE: Placing a small flat head screwdriver or similartool between the lamp outboard ball stud and plasticgrommet from inside the trunk can help to di
4. Twist and remove socket from lamp.5. Remove bulb from socket and replace.6. Reinstall the tail lamp, fasteners, and trunk liner.License Plate Lamp1
FLUID CAPACITIESU.S. MetricFuel (Approximate)All Engines — (Except 2.4L PZEV) 16.9 Gallons 64 Liters2.4L PZEV (Partial Zero Emissions Vehicle) 18.5 Ga
FLUIDS, LUBRICANTS AND GENUINE PARTSEngineComponent Fluid, Lubricant, or Genuine PartEngine Coolant We recommend you use MOPAR® Antifreeze/Coolant 10
Component Fluid, Lubricant, or Genuine PartSpark Plugs – 2.4L withPZEV*We recommend you use MOPAR® Spark Plugs (Gap 0.031 in [0.8 mm]).Spark Plugs – 3
MAINTENANCE SCHEDULESCONTENTS䡵 MAINTENANCE SCHEDULE ...476 ▫ Maintenance Chart...4788MAINTENANCESCHEDULES
MAINTENANCE SCHEDULEYour vehicle is equipped with an automatic oil changeindicator system. The oil change indicator system willremind you that it is t
• Check tire pressure and look for unusual wear ordamage. Rotate tires at the first sign of irregular wear,even if it occurs before the oil indicator
WARNING! (Continued)• Wearing your belt in the wrong place could makeyour injuries in a collision much worse. You mightsuffer internal injuries, or yo
Maintenance ChartMileage or time passed(whichever comes first)20,00030,00040,00050,00060,00070,00080,00090,000100,000110,000120,000130,000140,000150,0
Mileage or time passed(whichever comes first)20,00030,00040,00050,00060,00070,00080,00090,000100,000110,000120,000130,000140,000150,000Or Years: 2 3 4
Mileage or time passed(whichever comes first)20,00030,00040,00050,00060,00070,00080,00090,000100,000110,000120,000130,000140,000150,000Or Years: 2 3 4
** The spark plug change interval is mileage based only,yearly intervals do not apply.WARNING!• You can be badly injured working on or around amotor v
IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLE ...485▫ Prepare For The Appointment...
䡵 DEPARTMENT OF TRANSPORTATION UNIFORMTIRE QUALITY GRADES ...491▫ Treadwear...491▫ Traction Grades ...
SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you are having warranty work done, be sure to havethe right papers with
facilities, factory-trained technicians, special tools, andthe latest information to ensure the vehicle is fixedcorrectly and in a timely manner.This
In Mexico Contact:Av. Prolongacion Paseo de la Reforma, 1240Sante Fe C.P. 05109Mexico, D. F.In Mexico City: 5081-7568Outside Mexico City: 1-800-505-13
3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.”WARNING!•A belt that is buckled into the wrong
The manufacturer will not stand behind any servicecontract that is not the manufacturer’s service contract. Itis not responsible for any service contr
MOPAR® PARTSMOPAR® fluids, lubricants, parts, and accessories areavailable from an authorized dealer. They are recom-mended for your vehicle in order
PUBLICATION ORDER FORMSTo order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Mas-tercard, American Ex
Call toll free at:• 1–800–890–4038 (U.S.)• 1–800–387–1143 (Canada)OrVisit us on the Worldwide Web at:• www.techauthority.comDEPARTMENT OF TRANSPORTATI
WARNING!The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does notinclude acceleration, cornering, hydrop
INDEX10
About Your Brakes ...320ABS (Anti-Lock Brake System) ...322Adding Engine Coolant (Antifreeze) ...440Adding
Adding Fluid ...447Fluid and Filter Changes ...450Fluid Level Check ...447Fluid Type ...
Cellular Phone ...110Certification Label...375Chains, Tire ...353Changing A Fl
Pressure Cap ...441Radiator Cap ...441Selection of Coolant (Antifreeze) ...439Corrosion Protec
INTRODUCTIONCONTENTS䡵 INTRODUCTION ...4䡵 HOW TO USE THIS MANUAL ...4䡵 WARNINGS AND CAUTIONS ...6䡵 VEHICLE I
WARNING!•A belt that is worn under your arm is dangerous. Yourbody could strike the inside surfaces of the vehicle ina collision, increasing head and
Electronic Vehicle Information Center (EVIC) ...224Emergency, In Case ofJacking ...395Jump Starting ...
Exterior Lights ...99Fabric Care...454FCC General Information (Remote Keyless Entry) . . .27FCC Ge
Additives ...366Clean Air ...364Ethanol ...365Filler Cap (Gas Cap) ...
Hands-Free Phone (Uconnect®) ...110HazardDriving Through Flowing, Rising, or ShallowStanding Water ...317Hazard Warn
Interior Lights ...168Intermittent Wipers (Delay Wipers)...170Introduction ...4iPod®/USB/
Electronic Stability Program (ESP) Indicator ...330Engine Temperature Warning ...210Exterior ...99Fog ...
Lumbar Support ...153Maintenance Free Battery...429Maintenance Procedures ...424Maintenance S
Filter ...428Filter Disposal ...428Identification Logo ...426Materials Added to
Programmable Electronic Features ...233Radial Ply Tires ...345Radiator Cap (Coolant Pressure Cap) ...441Radio
Safety Tips ...95Satellite Radio Antenna ...260Schedule, Maintenance ...476Seat Belt M
WARNING!•A lap belt worn too high can increase the risk ofinjury in a collision. The belt forces won’t be at thestrong hip and pelvic bones, but acros
Side Window Demisters (Defrosters) ...284Signals, Turn ...99Snow Chains (Tire Chains)...353Snow Tir
Chains ...353Changing ...395Compact Spare ...348General Information ...
Trailer and Tongue Weight ...381Wiring ...386Trailer Towing Guide...380Trailer Weight...
Uconnect® (Hands-Free Phone) ...110Understanding Your Instrument Panel...206Uniform Tire Quality Grades ...491Univer
Windshield Washers ...169Fluid ...434Windshield Wiper Blades...434Windshield Wipers
INSTALLATION OF RADIO TRANSMITTINGEQUIPMENTSpecial design considerations are incorporated into this vehicle’selectronic system to provide immunity to
200Chrysler Group LLCOWNER’S MANUAL2014 20014C41-126-AC Third Edition Printed in U.S.A.
Lap/Shoulder Belt Untwisting ProcedureUse the following procedure to untwist a twisted lap/shoulder belt.1. Position the latch plate as close as possi
you will prefer a higher position. When you release theanchorage, try to move it up or down to make sure thatit is locked in position.Rear Seat BeltsT
Automatic Locking Retractor Mode (ALR) — IfEquippedIn this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove
Energy Management FeatureThis vehicle has a safety belt system with an EnergyManagement feature in the front seating positions to helpfurther reduce t
How The Active Head Restraints (AHR) WorkThe Occupant Restraint Controller (ORC) determineswhether the severity, or type of rear impact will requireth
CAUTION!All occupants, including the driver, should not oper-ate a vehicle or sit in a vehicle’s seat until the headrestraints are placed in their pro
4. The AHR front soft foam and trim half should lockinto the back decorative plastic half.1 — Downward Movement2 — Rearward Movement3 — Final Downward
NOTE:• If you have difficulties or problems resetting the ActiveHead Restraints, see an authorized dealer.• For safety reasons, have the Active Head R
INTRODUCTIONCongratulations on selecting your new Chrysler GroupLLC vehicle. Be assured that it represents precisionworkmanship, distinctive styling,
Light remains illuminated until the respective seat beltsare fastened. The driver should instruct all other occu-pants to fasten their seat belts. If
dealer can provide you with a seat belt extender. Thisextender should be used only if the existing belt is notlong enough. When it is not required, re
NOTE: The Driver and Passenger Advanced Front AirBags are certified to new Federal regulations.The Advanced Front Air Bags have a multistage inflatord
• Air Bag Warning Light• Steering Wheel and Column• Instrument Panel• Knee Impact Bolsters• Driver Advanced Front Air Bag• Passenger Advanced Front Ai
WARNING! (Continued)• Do not put anything on or around the air bagcovers or attempt to open them manually. You maydamage the air bags and you could be
When the air bag deploys, it opens the seam between thefront and side of the seat’s trim cover. Each air bagdeploys independently; a left side impact
• Being too close to the SAB and SABIC air bags duringdeployment could cause you to be severely injured orkilled.The system includes side impact senso
seriously injured or killed. Occupants, especially chil-dren, should not lean on or sleep against the door, sidewindows, or area where the SAB or SABI
The Advanced Front Air Bags will not deploy in allfrontal collisions, including some that may produce sub-stantial vehicle damage — for example, some
It also includes diagnostics that will illuminate the instru-ment cluster Air Bag Warning Light if a malfunction isnoted that could affect the air bag
1INTRODUCTION 5
Supplemental Seat-Mounted Side Air Bag (SAB)Inflator UnitsThe Supplemental Seat-Mounted Side Air Bags (SAB) aredesigned to activate only in certain si
Because air bag sensors estimate deceleration over time,vehicle speed and damage are not good indicators ofwhether or not an air bag should have deplo
If you do have a collision, which deploys the air bags, anyor all of the following may occur:• The nylon air bag material may sometimes causeabrasions
Maintaining Your Air Bag SystemWARNING!• Modifications to any part of the air bag systemcould cause it to fail when you need it. You couldbe injured i
Air Bag Warning LightYou will want to have the air bags ready toinflate for your protection in a collision. TheAir Bag Warning Light monitors the inte
• Whether or not the driver and passenger safety beltswere buckled/fastened;• How far (if at all) the driver was depressing theaccelerator and/or brak
WARNING!In a collision, an unrestrained child can become aprojectile inside the vehicle. The force required tohold even an infant on your lap could be
Summary Of Recommendations For Restraining Children In VehiclesChild Size, Height, Weight Or Age Recommended Type Of Child RestraintInfants and Tod-dl
Infants And Child RestraintsSafety experts recommend that children ride rearward-facing in the vehicle until they are two years old or untilthey reach
have outgrown the rear-facing weight or height limit oftheir rear-facing convertible child seat. Children shouldremain in a forward-facing child seat
WARNINGS AND CAUTIONSThis Owners Manual contains WARNINGS against op-erating procedures that could result in a collision orbodily injury. It also cont
seatback, should use the seat belt in a rear seat. Use thissimple 5-step test to decide whether the child can use thevehicle’s seat belt alone:1. Can
Recommendations For Attaching Child RestraintsRestraint TypeCombinedWeight of theChild + ChildRestraintUse any attachment method shown with an “X” Bel
Lower Anchors And Tethers For Children (LATCH)Restraint SystemYour vehicle is equipped with the child restraint anchor-age system called LATCH, which
LATCH Positions For Installing Child Restraints InThis Vehicle• Lower Anchorage Symbol 2 anchorages per seat-ing position•Top Tether Anchorage Symbol2
What is the weight limit (child’s weight +weight of the child restraint) for using theLATCH anchorage system to attach the childrestraint?65 lbs (29.5
Can two child restraints be attached using acommon lower LATCH anchorage?No Never “share” a LATCH anchorage with twoor more child restraints. If the c
Locating The LATCH AnchoragesThe lower anchorages are round bars that arefound at the rear of the seat cushion where itmeets the seatback, below the a
Locating The LATCH AnchoragesIn addition, there are tether strap anchoragesbehind each rear seating position located in thepanel between the rear seat
tether strap. The tether strap will have a hook at the endto attach to the top tether anchorage and a way to tightenthe strap after it is attached to
2. Loosen the adjusters on the lower straps and on thetether strap of the child seat so that you can moreeasily attach the hooks or connectors to the
NOTE: It is illegal to remove or alter the VIN.VEHICLE MODIFICATIONS/ALTERATIONSWARNING!Any modifications or alterations to this vehicle couldseriousl
with it and accidentally lock the seatbelt retractor. Beforeinstalling a child restraint using the LATCH system,buckle the seat belt behind the child
make a clicking noise while the webbing is pulled backinto the retractor. For additional information on ALR,refer to the “Automatic Locking Mode” desc
What is the weight limit (child’s weight +weight of the child restraint) for using theTether Anchor with the seat belt to attach aforward facing child
Installing A Child Restraint With A SwitchableAutomatic Locking Retractor (ALR)1. Place the child seat in the center of the seatingposition. For some
8. If the child restraint has a top tether strap and theseating position has a top tether anchorage, connectthe tether strap to the anchorage and tigh
between the two posts. If not possible, lower the headrestraint and pass the tether strap around the outboardside of the head restraint.1 — Cover A —
Transporting PetsAir Bags deploying in the front seat could harm your pet.An unrestrained pet will be thrown about and possiblyinjured, or injure a pa
NOTE: A new engine may consume some oil during itsfirst few thousand miles (kilometers) of operation. Thisshould be considered a normal part of the br
WARNING! (Continued)eventually poison you. To avoid breathing (CO),follow these safety tips:• Do not run the engine in a closed garage or inconfined a
Front seat belt assemblies must be replaced after acollision. Rear seat belt assemblies must be replaced aftera collision if they have been damaged (i
Comments to this Manuals